253-TALU-LSHG-C6-A5 Tyco Electronics, 253-TALU-LSHG-C6-A5 Datasheet - Page 8

• Manufacturer Part Number: 253-TALU-LSHG-C6-A5
• Description: Current Transducer
• Manufacturer: Tyco Electronics

Specifications of 253-TALU-LSHG-C6-A5

• Current Measuring Range Ac: 1A To 10A
• Sensor Output: Current
• Frequency Max: 60Hz
• Transducer Output Current Dc Max: 20mA
• Frequency Min: 50Hz
• Transducer Input Current Ac Max: 5A
• Output Current Max: 20mA
• Lead Free Status / RoHS Status: na

Paladin Transducers 250 Series Class 0.5
Tap Position Transmitter
For accurate remote indication of tap position selection on a high voltage
transformer. The variable tap position voltage is monitored, a D.C. output produced
which is proportional to the tap position.
Specification
Product Codes – Tap Position Transmitter, Auxiliary Powered
Slide Wire Transmitter
Designed for accurate measurements and transmission of resistance ratio of a 3 wire
potentiometer. A stabilised voltage is applied to the potentiometer and the voltage
measured from the zero to the end of the wiper. This is amplified and the D.C. output
produced is proportional to the resistance value.
Specification
Note:
Not all applications provide for the slider to mechanically travel the full distance
along the resistor track. Normally the first resistor step is inside the transducer and
its value should be stated when ordering, as well as the total track resistance. End of
track or connecting lead resistance, if significant, should also be considered. For
satisfactory operation, the change in resistance should be greater than 20% of the
total resistance.
Product Code – Side Wire Transmitter (3 wire), Auxiliary Powered
Input Span:
Outputs:
Auxiliary Power:
Input Span:
Outputs:
Auxiliary Power:
R1, R2, R3
(Specify)
10-50
Input
Taps
5-50
A.C. Aux Power
16
Ohm
120V
400
30
1-20k
5-50 taps at 400Ω each
10-50 taps at 30Ω each
0/1mA, 0/5mA, 0/10mA, 0/20mA, 4/20mA
A.C. 110, 120, 220, 240, 380, 415V
63.5, 139, 208, 277, 440, 480V
D.C. 12, 24, 48, 120, 135V
Minimum 1kΩ Max 50kΩ Specify values of R1, R2, R3
Example for 1k Potentiometer: R1 = 1k, R2 = 0, R3 = 1k
Example for 5k Potentiometer using only 4k;
R1 = 5k, R2 = 1k, R3 = 4k (Remember R1 = R2 + R3)
0/1mA, 0/5mA, 0/10mA, 0/20mA or 4-20mA,
0/1, 0/5, 0/10V D.C.
A.C. 110, 120, 220, 240, 380, 415V,
63.5, 139, 208, 277, 440, 480V
D.C. 12, 24, 48, 110, 120 or 135V
O/P D.C.
O/P D.C.
0/1mA
0/1mA
0/1mA
253-TRP*-TRFA-DG
253-TRT*-T5FA-DG
253-TRT*-TIFA-DG
Catalogue No.
Catalogue No.
Connection Diag.
Connection Diag.
12
12
12