D10DNFP BANNER ENGINEERING, D10DNFP Datasheet
D10DNFP
Specifications of D10DNFP
Related parts for D10DNFP
D10DNFP Summary of contents
Page 1
... D10DPFP D10DPFPG D10DPFPQ D10DPFPGQ * 9 m (30 ) cables are available by adding suffix “W/30” to the model number of any cabled sensor (e.g., D10DNFP W/ model with a QD connector requires a mating cable (see page 14). WARNING . . . Not To Be Used for Personnel Protection Never use these products as sensing devices for personnel protection. Doing so could lead to serious injury or death. ...
Page 2
... Banner Engineering Corp. Minneapolis, MN U.S.A. • www.bannerengineering.com • Tel: 763.544.3164 2.5 ms 100 µs Green 525 180 mm 320 mm 3 100 mm ...
Page 3
... Push Button • Single-click both buttons simultaneously. * NOTE: Triple-pulse will change the display, but will not save. To save Channel Select, make an adjustment to that channel as a TEACH, SET, or Sensor Setup. Banner Engineering Corp. Minneapolis, MN U.S.A. • www.bannerengineering.com • Tel: 763.544.3164 D10 Expert Sensor Programming 0.04 seconds ≤ ...
Page 4
... Figure 3. Contrast Values Sensing window size adjusted by Manual Adjust Result Output OFF Output ON Output OFF Darkest Single Most Light (no signal) sensing condition Banner Engineering Corp. Minneapolis, MN U.S.A. • www.bannerengineering.com • Tel: 763.544.3164 (saturated signal) (saturated signal) (saturated signal) ...
Page 5
... Dynamic (+) button. • Present Output ON/OFF conditions while continuing to hold Dynamic button. • Release Dynamic button. Banner Engineering Corp. Minneapolis, MN U.S.A. • www.bannerengineering.com • Tel: 763.544.3164 D10 Expert Dynamic TEACH and Adaptive Thresholds • TEACH on-the-fly. • Sets a single threshold. • Threshold position is adjustable using the “+” and “-” buttons (see Manual Adjust, page 9). ...
Page 6
... TEACH conditions unacceptable: • Display flashes “fail” and returns to “1st” • Arrow icon remains red • After 60 seconds, sensor returns to RUN mode (Arrow icon turns green) without changing settings. Banner Engineering Corp. Minneapolis, MN U.S.A. • www.bannerengineering.com • Tel: 763.544.3164 Most Light (saturated signal) ...
Page 7
... T T • P resent Output OFF condition • F our-click Static push button T Banner Engineering Corp. Minneapolis, MN U.S.A. • www.bannerengineering.com • Tel: 763.544.3164 D10 Expert Single-Point Light SET • S ets a threshold slightly below the taught condition (see Figure 7) • condition darker than the threshold condition causes the output to change state • T hreshold position is adjustable using “+” and “-” buttons (see Manual Adjust, page 9) • ...
Page 8
... Threshold Offset Mode (counts above taught signal value) Super High-Speed High-Speed High-Power Super High-Power Figure 10. Dark SET Threshold Offset Result Push Button Remote Banner Engineering Corp. Minneapolis, MN U.S.A. • www.bannerengineering.com • Tel: 763.544.3164 Most Light (saturated signal) Most Light (saturated signal ...
Page 9
... Sensing Window: • Adjusts sensing window size (tolerance) for the single-point target condition • Press “+” to increase; press “-” to decrease Push Button • Click “+” to increase, or click “-” to decrease. Banner Engineering Corp. Minneapolis, MN U.S.A. • www.bannerengineering.com • Tel: 763.544.3164 D10 Expert Manual Adjust Remote • ...
Page 10
... High-power RUN mode (1-ms response) • “HP” Super-high-power (2.5-ms response) • “SHP” • Quad-click the • See Advanced Setup (page 5). remote line to proceed Advanced Setup. Result Banner Engineering Corp. Minneapolis, MN U.S.A. • www.bannerengineering.com • Tel: 763.544.3164 ...
Page 11
... RUN mode. • Prevents unwanted adjustments or tampering of the push buttons. • Push buttons can be enabled or disabled only from the remote line and only during normal RUN mode. Push Button • Not available with push-button programming. Banner Engineering Corp. Minneapolis, MN U.S.A. • www.bannerengineering.com • Tel: 763.544.3164 D10 Expert Advanced Setup T T Remote 0.04 sec. ≤ T ≤ 0.8 sec. ...
Page 12
... Storage Temperature: -20° to +80°C (-4° to +175°F) Max. Rel. Humidity: 90% @ 50°C (non-condensing) Number of Devices, Stacked DIN rail or included mounting bracket Ambient Temperature Rating Specification 55°C 50°C 45°C Banner Engineering Corp. Minneapolis, MN U.S.A. • www.bannerengineering.com • Tel: 763.544.3164 Load 150 ...
Page 13
... Mounting Bracket (included) 35.1 mm (1.38") 10.0 mm (0.39") Banner Engineering Corp. Minneapolis, MN U.S.A. • www.bannerengineering.com • Tel: 763.544.3164 D10 Expert Dimensions 10.5 ± 0.2 mm (typ.) (0.41") 35.9 mm (1.41") 61.3 mm (2.42") 68.1 mm (2.68") Included Bracket Dimensions 10.0 mm (0.39") 5 3.5 mm (0.20") (0.14") 16.0 mm 15.2 mm (0.63" ...
Page 14
... Accessories Pico-Style Quick-Disconnect Cables Dimensions ø max max. (1.1" max. (1.0") ø12 mm max. (0.5") + – Pin-out (0.4") Brown Wire Gray Wire Pink Wire 20 mm (0.8") Banner Engineering Corp. Minneapolis, MN U.S.A. • www.bannerengineering.com • Tel: 763.544.3164 White Wire Blue Wire Black Wire ...
Page 15
... Banner Engineering Corp. Minneapolis, MN U.S.A. • www.bannerengineering.com • Tel: 763.544.3164 D10 Expert Dual Discrete Outputs ™ 15 P/N 64154 rev. F ...
Page 16
... P/N 64154 rev. F Banner Engineering Corp., 9714 Tenth Ave. No., Minneapolis, MN USA 55441 • Phone: 763.544.3164 • www.bannerengineering.com • Email: sensors@bannerengineering.com WARRANTY: Banner Engineering Corp. warrants its products to be free from defects for one year. Banner Engineering Corp. will repair or replace, free of charge, any product of its manufacture found to be defective at the time it is returned to the factory during the warranty period ...