E32-T61S Omron, E32-T61S Datasheet - Page 105
![Fiber-Optic Cable](/photos/19/89/198994/4472991_sml.jpg)
E32-T61S
Manufacturer Part Number
E32-T61S
Description
Fiber-Optic Cable
Manufacturer
Omron
Type
High Temperaturer
Datasheet
1.E32-DC50.pdf
(108 pages)
Specifications of E32-T61S
Fiber Optic Sensor Type
High Temperature
Rohs Compliant
Yes
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
- Current page: 105 of 108
- Download datasheet (2Mb)
E32
Installation
J SENSING HEAD
Mounting Sensing Head in a Panel
Prepare a hole in the panel that can accommodate the threaded
cylindrical sensing head. Be sure to place the washer in front of
the mounting nut before inserting the sensing head through the
hole. Tighten the front mounting nut using no more than the
maximum torque recommended in the table.
Mounting Sensing Head in a Channel
Insert the sensing head at the desired location in the channel as
shown in the illustration, then use a set screw to fasten the head
in place. Apply no more than 2.6 in-lb of force in tightening the
set screw.
Tightening Torque
Use a proper-sized
wrench and do not
exceed the torque
recommended for the
sensing head.
Sensing heads
M3 and M4 threads
M6 threads
2 mm dia., no thread
3 mm dia., no thread
E32-D14L
E32-T12F
E32-D12F
E32-T16
E32-R21
E32-M21
E32-L25A
Nuts
(attachment)
Retaining screw
(M 3 max.)
Spring mounting clip
Toothed washers
Maximum torque
6.88 in-lb
8.66 in-lb
2.6 in-lb
2.6 in-lb
8.66 in-lb
6.88 in-lb
6.88 in-lb
4.33 in-lb
5.2 in-lb
4.33 in-lb
6.88 in-lb
106
J CUTTING FIBER
Insert a fiber into the Fiber and determine the length of the fiber
to be cut.
Press down the Fiber Cutter in a single stroke to cut the fiber.
When the fiber is cut, an insertion mark is inscribed on the fiber.
Insert a fiber into the Fiber Cutter in the direction indicated by the
arrow (refer to the following figure).
The cutting holes cannot be used twice. If the same hole is used
twice, the cutting face of the fiber will be rough and the sensing
distance will be reduced. Always use an unused hole.
Use either one of the two holes on the right (refer to the following
figure) to cut a thin fiber as follows:
1. An attachment is temporarily fitted to a thin fiber before
2. Secure the attachment after adjusting the position of it in the
3. Insert the fiber into the E39-F4 to cut.
Note: Insert the fiber in the direction indicated by the arrow.
Three holes for
standard fiber
(2.2 mm dia.)
For a 2.2-mm dia. standard fiber only.
2
shipment.
direction indicated by the arrow.
12.6
2.2-dia.
Insertion mark
1
Temporarily fitted
Cutter E39-F4
Two holes for
thin fiber
E32
Related parts for E32-T61S
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
![E32-T21R](/photos/17/81/178177/grp_fiberopticf_tmb.jpg)
Part Number:
Description:
Proximity Sensors 2.2MM M3 HIGH FLEX T-BEAM
Manufacturer:
Omron
Datasheet:
![E32-T16P](/photos/17/81/178177/grp_fiberopticf_tmb.jpg)
Part Number:
Description:
FIBER,T-BEAM,THIN,11MM SLIT
Manufacturer:
Omron
Datasheet:
![E32-M21](/images/manufacturer_photos/0/4/494/omron_tmb.jpg)
Part Number:
Description:
4-HEAD T-BEAM FIBER
Manufacturer:
Omron
Datasheet:
![E32-T22R 2M](/images/manufacturer_photos/0/4/494/omron_tmb.jpg)
Part Number:
Description:
Fiber Optic Sensors HIGH FLEX T-BEAM 2mm DIA HEAD
Manufacturer:
Omron
Datasheet:
![E32-L56-2 2M](/images/manufacturer_photos/0/4/494/omron_tmb.jpg)
Part Number:
Description:
Fiber Optic Sensors FIBER FOR GLASS SHEE T DETECTN
Manufacturer:
Omron
![E32-UTAT1-3F](/images/manufacturer_photos/0/4/494/omron_tmb.jpg)
Part Number:
Description:
Fiber Optic Sensors SMALL DIA T-BEAM ARM ORED-3FT
Manufacturer:
Omron
Datasheet:
![G6S-2G](/images/no-image3.png)
Part Number:
Description:
G6S-2GLow Signal Relay
Manufacturer:
Omron Corporation
Datasheet:
![G3NE-220T](/images/no-image3.png)
Part Number:
Description:
Compact, Low-cost, SSR Switching 5 to 20 A
Manufacturer:
Omron Corporation
Datasheet:
![G6K-2G-Y](/images/no-image3.png)
Part Number:
Description:
Manufacturer:
Omron Corporation
Datasheet: