E3XNA41F2M Omron, E3XNA41F2M Datasheet - Page 3
![Photoelectric Sensor](/photos/19/85/198517/3753717_sml.jpg)
E3XNA41F2M
Manufacturer Part Number
E3XNA41F2M
Description
Photoelectric Sensor
Manufacturer
Omron
Type
High Speed Fiber Optic Sensorr
Datasheet
1.E3XNA11F2M.pdf
(28 pages)
Specifications of E3XNA41F2M
Sensor Output
PNP
Sensor Input
Fiber Optic
Output Type
PNP LO/DO
Supply Voltage Max
24V
Switch Terminals
Cable
Supply Voltage Min
12V
Fiber Optic Sensor Type
High Speed Fiber Optic Sensor
Rohs Compliant
Yes
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
E3X-NA
Specifications
I
Ratings/Characteristics
Note:
I
Item
Output type
Light source (wavelength)
Supply voltage
Current consumption
Control output
Operation mode Switch-
Response time
Sensitivity adjustment
Circuit protection
Timer function
Ambient illumination
(receiver side)
Ambient temperature
Ambient humidity
Insulation resistance
Dielectric strength
Vibration resistance
Shock resistance
Enclosure rating
Connection method
Weight (packed)
Material
Accessories
Item
Rated current
Rated voltage
Contact resistance
Number of insertions
Material
Weight (packed)
Amplifier Units
Amplifier Unit Connectors
When there are 8 or more Amplifier Units mounted side-by-side, the response time will be 350 µs max.
NPN output
PNP output
selectable
Case
Cover
Housing
Contact
Amplifier Units with Cables
Standard models
E3X-NA11
E3X-NA41
Red LED (680 nm)
12 to 24 VDC ±10%, ripple (p-p): 10% max.
35 mA max.
NPN/PNP (depends on model) open collector; load current: 50 mA max.; residual voltage: 1 V max.
Light-ON/Dark-ON operation
200 µs max. for operation
and reset respectively
(See note.)
8-turn sensitivity adjuster (with indicator)
Reverse polarity, output
short-circuit, mutual inter-
ference prevention (opti-
cally synchronized)
OFF-delay timer: 40 ms (fixed)
Incandescent lamp:10,000 lux max.
Sunlight:20,000 lux max.
Operating: Groups of 1 to 3 Amplifiers: −25°C to 55°C (-13°F to 131°F)
Groups of 4 to11 Amplifiers: −25°C to 50°C (-13°F to 122°F)
Groups of 12 to16 Amplifiers: −25°C to 45°C (-13°F t0 113°F) with no icing or condensation
Storage: −30°C to 70°C (-22 °F to 158°F) with no icing or condensation
Operating and storage: 35% to 85% (with no condensation)
20 MΩ min. (at 500 VDC)
1,000 VAC at 50/60 Hz for 1 minute
10 to 55 Hz with a 1.5-mm double amplitude for 2 hrs each in X, Y and Z directions
500 m/s
IEC60529 IP50 (with Protective Cover attached)
Prewired (standard cable length: 2 m)
Approx. 100 g
Polybutylene terephthalate (PBT)
Polycarbonate
Instruction Sheet
E3X-CN11
2.5 A
50 V
20 mΩ max. (20 mVDC max., 100 mA max.)
(The above figure is for connection to the Amplifier Unit and the adjacent Connector. It does not include the conductor
resistance of the cable.)
50 times (for connection to the Amplifier Unit and the adjacent Connector)
Polybutylene terephthalate (PBT)
Phosphor bronze/gold-plated nickel
Approx. 55 g
2
, for 3 times each in X, Y and Z directions
High-speed
detection
models
E3X-NA11F
E3X-NA41F
35 mA max.
(for 24-VDC
power supply)
Operation:
20 µs max.
Reset:
30 µs max.
Reverse
polarity, output
short-circuit
Mark-detecting
models
E3X-NAG11
E3X-NAG41
Green LED
(520 nm)
35 mA max.
200 µs max. for operation and reset respectively (See Note.)
Reverse polarity, output short-circuit, mutual interference prevention
(optically synchronized)
E3X-CN12
Approx. 25 g
Water-resistant
models
E3X-NA11V
E3X-NA41V
Red LED (680 nm)
IEC60529 IP66
(with Protective
Cover attached)
Approx. 110 g
Polyethersulfone
(PES)
Connector-ready amplifier units
Wire-saving
models
E3X-NA6
E3X-NA8
IEC60529
IP50 (with
Protective
Cover at-
tached)
Approx. 55 g Approx. 65 g
Polycarbon-
ate
Connector
Water-resistant
models (use M8
connectors)
E3X-NA14V
E3X-NA44V
500 VAC at 50/
60 Hz for 1 minute
IEC60529 IP66
(with Protective
Cover attached)
M8 connector
Polyethersulfone
(PES)
E3X-NA
3