SBF1 BANNER ENGINEERING, SBF1 Datasheet
SBF1
Specifications of SBF1
Available stocks
Related parts for SBF1
SBF1 Summary of contents
Page 1
... Modular design with interchangeable components (scanner blocks, power blocks, and logic timing modules); over 5,000 sensor configurations possible • Scanner blocks for opposed, retro, diffuse, convergent, and fiber optic sensing modes (including high-gain models) • Power blocks for operation, including 2-wire ac operation • ...
Page 2
... NOT be used as sensing devices for personnel protection. WARRANTY: Banner Engineering Corporation warrants its products to be free from defects for one year. Banner Engineering Corporation will repair or replace, free of charge, any product of its manufacture found to be defective at the time it is returned to the factory during the warranty period. ...
Page 3
MULTI-BEAM Sensors E71083 Banner MULTI-BEAM ® sensors are compact modular self con- tained photoelectric switches. Each MULTI-BEAM consists of three components: scanner block, power block, and logic module. The scanner block contains the complete modulated photoelectric amplifier as well as ...
Page 4
... SBDX1 SBDX1MD SBCV1 SBCVG1 SBC1 SBC1-4 SBC1-6 SBCX1 SBCX1-4 SBCX1-6 SBEF & SBRF1 SBEXF & SBRXF1 SBFX1 SBF1 SBF1MHS SBFV1 SBFVG1 SBAR1 SBAR1GH SBAR1GHF 4 Upper Cover (lens) (supplied with Scanner Block) Lower Cover (supplied with Scanner Block) (pages 6 through 23) Sensing Mode ...
Page 5
... Scanner Blocks Model SBE & 2SBR 2SBL1 2SBD1 2SBDX1 2SBC1 2SBC1-4 2SBF1 (pages 6 through 23) Input Voltage Output Configuration 10 to 30V dc SPST NPN (sink), 250mA maximum 10 to 30V dc SPDT NPN (sink), 250mA each output 10 to 30V dc SPST PNP (source), 250mA maximum ...
Page 6
Systems (pages 24 through 29) Power Blocks Model 2PBD 2PBA 2PBB 2PBR 2PBR2 Logic Modules Model 2LM3 2LM5 2LM5R 2LM5-14 2LM5T 2LM4-2 LMT MULTI-BEAM Other Systems Edgeguide Systems (data sheet 03506) MULTI-BEAM 3- & 4-WIRE SCANNER BLOCKS DESCRIPTION MULTI-BEAM ...
Page 7
MULTI-BEAM Sensing Mode OPPOSED Mode OBJECT 3- & 4-wire Scanner Blocks Models Excess Gain SBE/SBR1: this opposed pair has the highest gain available response. SBED/SBRD1: fast response and small effective beam; will detect objects as small as ...
Page 8
MULTI-BEAM Sensing Mode RETROREFLECTIVE Mode RETRO TARGET OBJECT NOTE: for detailed information on available retroreflective materials, see the Banner product catalog & 4-wire Scanner Blocks Models Excess Gain SBLV1: visible beam makes alignment very easy, and is the ...
Page 9
MULTI-BEAM Sensing Mode DIFFUSE Mode OBJECT APPLICATION NOTE general rule regarding background objects in diffuse sens- ing, verify that the distance to the nearest background object is at least three times the distance from the sensor to the ...
Page 10
MULTI-BEAM Sensing Mode CONVERGENT Mode OBJECT Counting radiused products 10 3- & 4-wire Scanner Blocks Models Excess Gain SBCV1: .06-inch (1.5mm) dia. visible red spot, for precise positioning, edge-guiding, & small parts detection. Sensor-to-product distance must be consistent. Some products ...
Page 11
... SBEF & SBRF1: use with individual glass fiber optic assemblies in lieu of model SBF1 where it is inconvenient to run fibers from a single scanner block. SBEXF & SBRXF1: use in place of model SBFX1 (shown below) for long-range opposed fiber optic sensing. ...
Page 12
... Diffuse mode .05 I BT13S .025 .025 S .05 .075 0 .5 1.0 DISTANCE TO 90% WHITE TEST CARD--INCHES 10 IN 100 IN DISTANCE SBF1MHS 3 with IT23S SBF1MHS opposed mode fibers and 2 L9 lenses with IT23S IT13S C 0 fibers H IT23S OPPOSED DISTANCE--INCHES 10 IN 100 IN ...
Page 13
... OBJECT Scanner block model SBFV1 supplies visible red light to the emitter half of a glass fiber optic photoelectric system. Visible light sensors have less optical energy as compared to infrared systems. There are, however, some sensing situations which require visible light wavelengths in order to realize adequate optical contrast. ...
Page 14
... This modification is designated by adding suffix "MHS" to the scanner block model number (e.g.- SBF1MHS, etc.). High speed is most often required in fiberoptic or opposed mode sensing. The MHS modification reduces the available excess gain by about 50%, and also decreases the sensor's immunity to some forms of electrical " ...
Page 15
MULTI-BEAM DC Models PBT Input 30V dc at less than 60mA (current draw depends on scanner block used). 10% max. ripple. Output: one open-collector NPN transistor (sinks current to negative side of power supply). 250mA maximum. On state ...
Page 16
MULTI-BEAM DC Models These are power blocks for emitter scanner blocks only (models SBE, SBED, SBEX, SBEV, SBEXD, SBEF, SBEXF). Emitter assemblies do not require logic modules. PBT-1 Input 30V dc at less than 60mA (current draw depends ...
Page 17
MULTI-BEAM Hookup Diagrams for DC Power Blocks (continued) Hookup to MAXI-AMP Logic Module The current sinking output(s) of MULTI-BEAM power block models PBT and PBT2 may be connected directly to the input of CL Series MAXI-AMP modules. A MAXI-AMP which ...
Page 18
MULTI-BEAM AC Models PBAT Input: 105 to 130V ac, 50/60Hz. Output: SPST isolated solid-state switch; 100mA maximum (no inrush capacity), 200V dc max., 140V ac max. On-state voltage drop: less than 3 volts at full load. Off-state leakage current: less ...
Page 19
MULTI-BEAM AC Models PBAQ Input: 105 to 130V ac, 50/60Hz. Output: SPST isolated solid-state switch; nor- mally closed, 3/4 amp maximum (derated to 1/2 amp at 70 degrees C). Maximum inrush: 10 amps for one second or 30 amps for ...
Page 20
MULTI-BEAM Hookup Diagrams for AC Power Blocks (continued) Hookup in Parallel with other MULTI-BEAMs Any number of 3- & 4-wire L1 MULTI-BEAM power block outputs may be connected in parallel to a load. Parallel sen- PBA sor connection is usually ...
Page 21
MULTI-BEAM Functional Schematic RESPONSE TIME: response time will be that for the scanner block (plus power block) plus the programmed delay (if the logic includes a delay function). Model and Function LM1 on-off OUTPUT SIGNAL LM2 alternate action OUTPUT SIGNAL ...
Page 22
MULTI-BEAM Model and Function LM4-2NR one-shot (non-retriggerable) Pulse Pulse Pulse OUTPUT SIGNAL Setable time range second. LM5 on-delay Delay OUTPUT SIGNAL Setable time range: 1 seconds. LM5R off-delay Hold Hold OUTPUT SIGNAL Setable time range: ...
Page 23
MULTI-BEAM Model and Function LM8 repeat cycler Delay Hold Delay Hold Delay Hold OUTPUT SIGNAL Setable time range: 1 seconds. LM8-1 delayed one-shot Delay Hold Delay Hold OUTPUT SIGNAL Setable time range: 1 seconds. LM8A on-delay ...
Page 24
MULTI-BEAM 2-wire Sensors 2-wire MULTI-BEAM Functional Schematic, 2-wire MULTI-BEAM MULTI-BEAM 2-Wire Scanner Blocks SPECIFICATIONS SUPPLY VOLTAGE: connections are made via a 2-wire power block (see page 27). RESPONSE TIME: 10 milliseconds ON and OFF (3000 operations per minute). NOTE: a ...
Page 25
MULTI-BEAM Sensing Mode OPPOSED Mode OBJECT RETROREFLECTIVE RETRO TARGET OBJECT CONVERGENT Mode OBJECT 2-wire Scanner Blocks Models Excess Gain 1000 SBE & 2SBR1 100 E Range: 150 feet (45m Response: 10ms on/off G 10 Repeatability: ...
Page 26
... N with small parts, fast response L9 lenses time is often a considera tion. If the application re- DISTANCE quires response near the 10 millisecond specification of the 2SBF1, consider the 1000 faster 3- & 4-wire model 2SBF1 E SBF1 100 Range based on 90% reflectance S white test card S ...
Page 27
MULTI-BEAM MULTI-BEAM 2-wire power block models 2PBA, 2PBB, and 2PBD contain a low voltage power supply which utilizes a unique circuit to take a very small leakage current through the load and convert it to the dc power required to ...
Page 28
MULTI-BEAM Hookup Diagrams for 2-wire Power Blocks NOTE: output has maximum load capacity of 3/4 amp; maximum resistive load 15K ohms, minimum inductive load 1.2 watts (10mA) Basic Hookup of 2-wire MULTI-BEAM (See Specifications) 2PBA 2PBB 2PBD ...
Page 29
MULTI-BEAM SPECIFICATIONS, 2-WIRE LOGIC MODULES: specifications for 2-wire logic modules are identical to those for 3- and 4-wire logic modules (see page 21). Model and Function 2LM3 on-off OUTPUT SIGNAL 2LM4-2 one-shot Hold Pulse Pulse OUTPUT SIGNAL Setable time range: ...
Page 30
... UC-C4 4 inch (10cm) focus, glass lenses UC-C6 6 inch (15cm) focus, glass lenses UC-F ( Used on: SBF1, SBF1MHS, SBFX1, SBFV1, 2SBF1). Fits all Banner fiberoptic assemblies. UC-L Used on: SBE SBEV SBEX SBR1 SBRX1 SBL1 SBLV1, SBLX1, SBDL1, SBDX1, SBAR1, SBAR1GH, 2SBR1, 2SBL1, 2SBDX1, ...
Page 31
MULTI-BEAM Accessories Mounting Brackets SMB700 Model (right general-purpose two-axis mount- ing bracket that is supplied with a cable gland assembly which is used to attach the MULTI-BEAM wiring base to the bracket. The gland assembly is threaded through ...
Page 32
... NOT be used as sensing devices for personnel protection. WARRANTY: Banner Engineering Corporation warrants its products to be free from defects for one year. Banner Engineering Corporation will repair or replace, free of charge, any product of its manufacture found to be defective at the time it is returned to the factory during the warranty period. This warranty does not cover damage or liability for the improper application of Banner products ...