PM-L54 PANASONIC EW, PM-L54 Datasheet - Page 8
![no-image](/images/manufacturer_photos/0/5/513/panasonic_ew_sml.jpg)
PM-L54
Manufacturer Part Number
PM-L54
Description
PHOLOELECTRIC SENSOR
Manufacturer
PANASONIC EW
Datasheet
1.PM-L54.pdf
(12 pages)
Specifications of PM-L54
Output Current
50mA
Sensor Output
NPN Open Collector
Supply Voltage Range Dc
5V To 24V
Sensing Range
0mm To 5mm
Rohs Compliant
Yes
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
PM-L54
Manufacturer:
EVERLIGHT
Quantity:
38 790
PRECAUTIONS FOR PROPER USE
1 Insert a connector straight into a
2 When unplugging, give as much
Cautions in plugging or unplugging a connector
Crimping of hook-up connectors CN-14H and CN-14H-2
Item
Conductor cross-
section area
Wire diameter
Wire insulation
material
Procedures of plugging or unplugging a connector
Caution: Be sure to hold a connector
sensor until the connector lug is
locked by the sensor hook.
stress as a connector lug can be
relieved from a hook. Then unplug it.
Model No.
PM- 54
PM- 54P
when plugging or unplugging
it. Do not hold a terminal or a
cable when plugging or
unplugging the connector.
Otherwise, it will cause a
poor contact.
Do not plug or unplug a connector more than 10
times.
Be sure not to give stress more than 5 N to a ter-
minal of both a connector and a sensor.
If you do not follow the above cautions, it will
cause a poor contact.
(AWG28 to AWG24) (AWG25 to AWG24)
"0.028 to "0.047 in "0.047 to "0.060 in
"0.7 to "1.2 mm "1.2 to "1.52 mm
0.08 to 0.2 mm
Vinyl chloride or soft poly-
ethylene
CN-14H
2
0.18 to 0.22 mm
CN-14H-2
2
Conductor cross-section area
Wire diameter
5 N or less
Cable diameter
Hook
Lug
1 Strip the cable sheath 15 mm
2 Crimp with the exclusive
Notes: 1) When attaching or detach-
Notes:
Soldering (Both connector CN-14 and sensor)
Soldering temperature 260 C
Soldering time
Soldering position Refer to the below figure
Crimping method
Caution: Make sure to use the exclusive hook-up pliers CN-HP.
Prior to using the sensor, affix the cable in a way as to
avoid direct stress on the crimped part.
If soldering is done directly on the terminals, strictly
adhere to the conditions given below.
Sensor
wires into the connector insertion holes till the wire tips reach
the end.
hook-up pliers CN-HP.
Arrangement of connector terminals
Note: Wire at Pin No.1 or 2 as per requirement.
2) After crimping, do not pull
V 1
ing the connector fitted with
a cable, make sure to hold
the connector firmly before
proceeding.
on the cable.
V
Commercially available pliers cannot be used.
1
1
15 mm
2 0 V
2
2
0V
0V
0.591 in
3 sec. or less
0 V : 0 V
V:
1: Output 1 (Light-ON)
2: Output 2 (Dark-ON)
500 F
or more
Refer to
V
or less
Connector
Lead wire
(Do not strip the wire insulation.)
p.1135l
0.591
V 1
in, or more, and insert the
Cable sheath
2 0 V
(Note)
for general precautions.
1.5 mm
0.059 in
Power supply
Soldering
position
PM
345