QS18EN6DV BANNER ENGINEERING, QS18EN6DV Datasheet - Page 5
![Photoelectric Sensor](/photos/19/94/199468/4608904_sml.jpg)
QS18EN6DV
Manufacturer Part Number
QS18EN6DV
Description
Photoelectric Sensor
Manufacturer
BANNER ENGINEERING
Datasheet
1.QS18EN6D.pdf
(8 pages)
Specifications of QS18EN6DV
Output Current
100mA
Sensor Output
NPN
Supply Voltage Range Dc
10V To 30V
Sensor Housing
Rectangular
Sensor Input
Optical
Body Material
ABS
Supply Voltage Max
30VDC
Sensing Range Max
600mm
Figure 7. Window SET (Light Operate shown)
Access SETUP functions directly from RUN mode, using the procedures detailed below.
30 ms OFF-Delay (Pulse Stretcher) Enable/Disable
Light-Operate/Dark-Operate Select
* Initial Output LED condition is simultaneous with Power LED 3-flash.
(no signal)
(no signal)
(no signal)
(no signal)
Darkest
Darkest
Darkest
threshold ≈12.5% above
the presented condition
Output OFF
Banner Engineering Corp. • Minneapolis, MN U.S.A.
Sensor positions
www.bannerengineering.com • Tel: 763.544.3164
Output OFF
Output OFF
• F rom RUN mode, seven-click
• P ress and hold push button
• Present sensing condition.
• Double-click push button.
• F rom RUN mode, six-click the
0.04 seconds ≤ “Click” ≤ 0.8 seconds
0.04 seconds ≤ “Click” ≤ 0.8 seconds
0.04 seconds ≤ “Click” ≤ 0.8 seconds
the push button.
2 – 4 seconds.
push button.
Presented
Condition
Single
Presented
Condition
T
T
T
T
Output
Push Button
Single
T
T
ON
Push Button
Push Button
> 2 seconds
12.5%
> 2 seconds
Single
Presented
Condition
T
T
T
Sensor positions
threshold ≈12.5% below
the presented condition
> 2 seconds
Output ON
Output ON
Sensor positions
window thresholds
≈12.5% from the
presented condition
T
T
Output OFF
6
T
Most Light
Most Light
Most Light
(saturated
(saturated
(saturated
(saturated
7
T T T
T
T T T
T
signal)
signal)
signal)
signal)
T
T
2
T
T
T
T
T T T
T
T
T
T
T
T
T
T
T
• F rom RUN mode, seven-pulse
T
T
T
• Single-pulse remote line.
• P resent sensing condition.
• Double-pulse remote line.
• F rom RUN mode, six-pulse
T
T
remote line.
T
T
remote line.
T
T
T
0.04 seconds ≤ T ≤ 0.8 seconds
T
0.04 seconds ≤ T ≤ 0.8 seconds
0.04 seconds ≤ T ≤ 0.8 seconds
• S ingle ON condition window extends approximately 12.5% above and below the presented
• Lighter or darker conditions (“outside” the window) cause the output to change state.
• R ecommended for applications where the target to be sensed may not always appear in the
T
T
T
T
T
condition when Light Operate is selected (see Figure 7). Output ON and OFF conditions can be
reversed by changing the Light-/Dark-Operate setting (see below).
same place, or when other unwanted signals may appear.
T
T
T
T
T
T
T
T
T
T
T
Remote Line
T
T
T
T
T
T
T
Remote Line
Remote Line
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
Single-point Light SET (LO)
T
Window Set (LO)
T
T
T
T
T
T
T
T
T
T
T
T
Dark SET (LO)
T
T
T
> 2 seconds
T
Sensor SETUP
T
T
T
T
T
0.8 seconds
T
T
T
T
T
T
T
0.8 seconds
T
T
T
0.8 seconds
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
Sensor toggles between Light-/Dark-Operate settings and returns to RUN
mode.
Power LED: Flashes 3x, then ON Green
Output LED: L ight Operate – ON,*
WORLD-BEAM
Sensor waits for sensing condition.
Power LED: OFF
Output LED: Slow flash (1 Hz)
Sensor toggles between enable/disable settings and returns to RUN
mode.
Power LED: Flashes 3x, then ON Green
Output LED: E nabled – ON,*
T T T
T
T
T
T
T
T
Power LED: Flashes 3x, then ON Green
Output LED: OFF,* then ON or OFF, depending on output state
Sensor returns to RUN mode with new settings.
Power LED: OFF
Output LED: Slow flash (1 Hz)
Sensor returns to wait state, ready for sensing condition.
T
T
Push Button
Window SET
T
T
Dark Operate – OFF,*
Then ON or OFF, depending on output state
Disabled – OFF,*
Then ON or OFF, depending on output state
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
Result
T
T
T
Result
Result
0.8 seconds
T
T
T
®
Power LED: OFF
Output LED: Double-flash
T
T
T
QS18E Series
T
T
T
T
T
T
Remote Line
P/N 136564 rev. A
5