QS30LLP BANNER ENGINEERING, QS30LLP Datasheet - Page 3

• Manufacturer Part Number: QS30LLP
• Description: Photoelectric Sensor
• Manufacturer: BANNER ENGINEERING
• Type: Retroreflectiver

Specifications of QS30LLP

• Sensing Range: 0.2m To 18m
• Output Current: 150mA
• Sensor Output: NPN/PNP
• Supply Voltage Range Dc: 10V To 30V
• Sensor Housing: Rectangular
• Sensing Range Min: 0.2m
• Sensor Input: Laser
• Body Material: ABS Plastic
• Brand/series: QS30
• Cable Type: 2 m, 5 Wire Cable
• Current, Switching: 150 mA
• Function: Proximity
• Ip Rating: IP67
• Light Source: LED
• Material, Housing: ABS Plastic
• Mounting Type: Threaded
• Output: NPN/PNP
• Primary Type: Photoelectric
• Range, Measurement: 18 m
• Repeatability: 70 ms
• Response Time: 500 ms
• Sensing Mode: Retro-Reflective
• Standards: CE Marked
• Technology: Photoelectric
• Temperature, Operating: -10 to +50 °C
• Termination: Cable
• Voltage, Supply: 10-30 VDC
• Lead Free Status / Rohs Status: RoHS Exempt Product

Figure 3. Background Suppression SET
*Segments 7 and 8 simultaneously flashing: Indiscernible target; sensor defaults to maximum cutoff.
Segments 1 and 2 simultaneously flashing: Background is nearer than minimum cutoff; sensor defaults to minimum cutoff.
Minimum
Range
Banner Engineering Corp.
• Present background condition.
• Press and hold Background (+)
• Sampling continues until the
www.bannerengineering.com • Tel: [phone]
Objects in this area are sensed
push button > 2 seconds
(until indicators flash).
push button is released; then
sensor returns automatically
to RUN mode.
Sensing Distance (D)
Push Button
Sensing Distance
Approx. 5% of
•
Minneapolis, MN U.S.A.
Cutoff
WORLD-BEAM
The sensor’s cutoff point is set using a simple procedure, via either the push buttons
or the remote wire. Three methods are available: Background Suppression SET, Object
Detection SET, and Dynamic SET (remote only). After the sensor has been set for the
target application, manual adjustments (via the “+” and “–” push buttons) may be used
to fine-tune the cutoff point. Sensor output configuration (N.O./N.C.) and the OFF-delay
function are also set via the push buttons.
The Remote Configuration function may be used to configure the sensor remotely
or to disable the push buttons for security. Connect the gray wire of the sensor to
ground (0V dc), with a remote switch connected between them. Pulse the remote line
according to the diagrams in the configuration procedures. The length of the individual
pulses is equal to the value T:
The distance to the background is sampled; the sensor places the cutoff point at
approximately 95 percent of the distance to the background. In RUN mode, objects
located between the minimum range and the taught cutoff are sensed; anything beyond
the cutoff (e.g., other objects or background surfaces) is ignored.
Minimum range varies, depending on the cutoff distance and reflectivity (see
Figure 11).
• Present background condition.
• Single-pulse the remote line.
• Sensor returns to RUN mode.
0.04 seconds ≤ T ≤ 0.8 seconds
Remote
T
®
T
Background Suppression SET
QS30AF Adjustable-Field Sensor
0.04 seconds ≤ T ≤ 0.8 seconds
> 2 seconds
Remote Configuration
Sensor Configuration
T T T
T
T
T
T
T
T
• Indicator segments
• If cutoff is accepted, sensor returns
• If cutoff is beyond sensor range,
T
7 and 8 alternately
flash.
directly to RUN mode.
Feedback is displayed for 2 seconds (see
page 6).*
T
T
T
Result
P/N 111384 rev. D
3