PD45VP6LLPQ BANNER ENGINEERING, PD45VP6LLPQ Datasheet - Page 5

• Manufacturer Part Number: PD45VP6LLPQ
• Description: Photoelectric Sensor
• Manufacturer: BANNER ENGINEERING

Specifications of PD45VP6LLPQ

• Output Current: 150mA
• Sensor Output: PNP
• Supply Voltage Range Dc: 10V To 30V
• Sensing Range Max: 10.6mm
• Leaded Process Compatible: No
• Peak Reflow Compatible (260 C): No
• Sensor Input: Laser

Sensing Beam
Supply Voltage
Beam Size at Aperture
Beam Divergence
Supply Voltage
Laser Classification
Supply Protection Circuitry
Delay at Power Up
Output Configuration
Output Rating
Output Protection
Output Response Time
Repeatability
Adjustments
Extinguishing Wire
Indicators
Construction
Environmental Rating
Connections
Operating Conditions
Weight
Application Notes
Certifications
(all models except
PD45V..C300 Series)
Banner Engineering Corp.
www.bannerengineering.com • Tel: [phone]
•
Minneapolis, MN U.S.A.
Visible red Class 2 laser, 650 nm
10 to 30V dc (10% max ripple) at less than 20 mA, exclusive of load
3.75 mm x 1.85 mm (0.15" x 0.07") (Retroreflective Models)
Approximately 1 milliradian (Retroreflective Models)
10 to 30V dc (10% maximum ripple) at less than 20 milliamps, exclusive of load
Class 2 safety (CDRH (FDA) 1040.10 and IEC 60875-1)
Protected against reverse polarity, over voltage, and transient voltages
< 1 second
SPDT (complementary) solid-state switch; choose NPN (current sinking) or PNP (current sourcing) models
Light operate:
Dark operate:
150 mA maximum (each output)
OFF-state leakage current: < 1 microamp at 30V dc
ON-state sat u ra tion voltage: < 0.3V at 10 mA dc; < 0.8V at 150 mA dc
Protected against continuous overload or short-circuit of outputs; Overload trip point ≥ 220 milliamps
0.2 milliseconds (200 microseconds) ON and OFF
50 microseconds
12-turn slotted brass Gain (sensitivity) adjustment potentiometer (clutched at both ends of travel)
Gray wire held “low” for laser operation; “high” to turn laser OFF; Low ≤ 1.0V dc;
High ≥ V
Two LEDs: Green and Yellow
Housings are heat-resistant ABS alloy, UL94-VO rated; acrylic lens cover
NEMA 3; IEC IP54
2 m (6.5') or 9 m (30') attached cable, or 5-pin Euro-style 150 mm (6") pigtail quick-dis con nect
fitting; mating cables for QD models are ordered separately (see page 6).
Temperature: -10° to +45°C (+14° to +113°F)
Maximum relative humidity: 90% at 50°C (non-condensing)
Sensor only: 22g (0.8 oz)
Sensor plus 2 m cable: 62g (2.2 oz)
False pulse may occur < 1 second after power-up
Green glowing steadily:
Yellow glowing steadily: light is sensed; normally open output is conducting
Green blinking:
Yellow blinking:
supply
-4.0V dc (< 30V dc) or disconnect wire; 100 ms delay upon enable
Normally-open output conducts when the sensor sees its own modulated light
Normally-closed output conducts when the sensor sees dark
Specifications
power to sensor is ON
output overloaded
marginal excess gain
PD45 Series PicoDot
®
Sensors
P/N 115700
5