SBC1 BANNER ENGINEERING, SBC1 Datasheet - Page 16
![Photoelectric Sensor](/photos/19/83/198320/3788383_sml.jpg)
SBC1
Manufacturer Part Number
SBC1
Description
Photoelectric Sensor
Manufacturer
BANNER ENGINEERING
Datasheet
1.LM1.pdf
(32 pages)
Specifications of SBC1
Turn On Time
1ms
Sensor Housing
Rectangular
Sensor Input
Optical
Turn Off Time
1ms
Sensing Mode
Convergent
Range
1.5" Focal Point
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Part Number:
SBC1-100-172
Manufacturer:
NEC
Quantity:
20 000
Part Number:
SBC1-101-571
Manufacturer:
NEC
Quantity:
20 000
Part Number:
SBC1-102-211
Manufacturer:
NEC
Quantity:
20 000
Part Number:
SBC1-150-162
Manufacturer:
NEC
Quantity:
20 000
Part Number:
SBC1-151-431
Manufacturer:
NEC
Quantity:
20 000
16
These are power blocks for emitter scanner blocks only (models SBE, SBED, SBEX, SBEV, SBEXD, SBEF, SBEXF). Emitter assemblies do
not require logic modules.
MULTI-BEAM
PBT-1
Input: 10 to 30V dc at less than 60mA (current draw
depends on scanner block used). 10% max. ripple.
PBT48-1
Hookup Diagrams for DC Power Blocks
Input: 44 to 52V dc at less than 60mA (current draw
depends on scanner block used). 10% max. ripple.
When using power blocks with current sinking (NPN)
outputs, simple loads connect between the power block
output (terminal #3) and the positive supply (terminal
#1).
Any number of MULTI-BEAMs may be connected in parallel to one load to create "LIGHT-OR" (light operate
mode) or "DARK-OR" (dark operate mode) multiple sensor logic. In most situations, MULTI-BEAM dc power
blocks cannot wire in series. However, addition of an interposing relay with a normally closed contact or a Banner
logic module will permit "AND" logic with a parallel sensor array.
Hookup to DC Relay or Solenoid
(using sinking output)
Parallel Hookup to a Common Load
Hookup to a Programmable Controller
requiring a current sink
Use power blocks with NPN
outputs to interface to PLCs and
other logic devices requiring a
current sink at the inputs. Con-
nect the output of the power
block (terminal #3) to any input
of the PLC. Also connect the
negative of the MULTI-BEAM
power supply (terminal #2) to
the negative of the PLC power
supply.
To load requiring current sink:
LOAD
+
DC Models
PBT
PBT2
PBT48
LOAD
10 to 30V dc: PBT, PBT2
44 to 52V dc: PBT48
1
3
PBT2
PBT
+10 to 30V dc
3
1
4
2
4
2
30V dc
+10
1
3
to
PBT2
PBT
-
4
2
1
3
PBT2
PBT
4
2
To load requiring current source:
3- & 4-wire DC Power Blocks
+
When using power blocks with current sourcing (PNP)
outputs, simple loads connect between the power block
output (terminal #3) and dc common (terminal #2).
Hookup to DC Relay or Solenoid
(using sourcing output)
+
Connections
3
1
dc com
dc +
PBP
(See Specifications)
1
2
3
4
5
6
7
8
+
4
2
1
PBP
PBP48
N
P
U
S
T
10 to 30V dc
V dc
I
g.
44 to 52V dc: PBP48
P
C
r
o
r
l.
t
10 to 30V dc: PBP
2
3
1
3
1
PBP
4
2
-
Hookup to a Programmable Controller
requiring a current source
Use power blocks with PNP out-
puts to interface to PLCs and
other logic devices requiring a
current source at the inputs. Con-
nect the output of the power block
(terminal #3) to any input of the
PLC. Also connect the negative
of the MULTI-BEAM power
supply (terminal #2) to the nega-
tive of the PLC power supply.
4
2
LOAD
LOAD
-
-
Functional Schematic
Hookup of DC Emitter
MULTI-BEAM emitter-only scanner blocks use dc power
block models PBT-1 or PBT48-1. These power blocks
connect directly across the dc supply, as shown.
A logic zero (0 volts dc) is applied to the gate input
when the MULTI-BEAM output is energized. When
de-energized, a logic one is applied. The logic supply
must be common to the MULTI-BEAM supply nega-
tive.
Hookup to Logic Gate
30V dc
Emitter models:
SBE
SBED
SBEX
SBEV
SBEXD
SBEF
SBEXF
+10
to
(-) dc
* Use pullup resistor
+5V to 30V dc
logic supply
to logic supply
1
3
PBP
Output capacity: 250mA
maximum, each output.
4
2
*
+
+
10 to 30V dc
10 to 30V dc
1
PBT-1
3
1
PBT2
PBT
dc com
4
2
dc+
2
1
2
3
4
5
6
7
8
-
N
P
U
T
S
I
-
g.
P
o
C
l.
r
t
r