E2EM-X16MX1 2M Omron, E2EM-X16MX1 2M Datasheet - Page 7

• Manufacturer Part Number: E2EM-X16MX1 2M
• Description: Inductive Proximity Sensor
• Manufacturer: Omron

Specifications of E2EM-X16MX1 2M

• Sensor Input: Inductive
• Sensing Range: 16mm
• Supply Voltage Range Dc: 10V To 30V
• Supply Voltage Max: 30VDC
• Sensing Range Max: 16mm
• Switch Terminals: Wire Leaded
• Supply Voltage Min: 10VDC
• Output Type: NO
• Sensor Output: NO
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

● Mounting
Tightening Force
Do not tighten the nut with excessive force.
A washer must be used with the nut.
Dimensions
Pre-wired Models (Shielded)
E2EM-X2C@
E2EM-X8@@
15 dia.
13
29 dia.
24
M8 × 1
M18 × 1
3
26
Toothed washer
30
Two clamping nuts
4
8
Shielded Models
1. 4-dia. vinyl-insulated round cable with 2/3 conductors
2. Operation indicator (yellow)
1. 6-dia. vinyl-insulated round cable with
2. X1 Models: Operation indicator (red) Setting
(Conductor cross section: 0.3 mm
Insulator diameter: 1.3 mm), Standard length: 2 m
The cable can be extended up to 200 m
(separate metal conduit).
Indicator *2
38
2/3 conductors (Conductor cross section: 0.5 mm
Insulator diameter: 1.9 mm), Standard length: 2 m
indicator (green)
X2 Models: Operation indicator (red)
C Models: Operation indicator (yellow)
Part B Part A
Toothed washer
43
7
Two clamping nuts
2
10
*1
Indicator *2
12
Unshielded Models
Part B Part A
Mounting Hole
2
,
Dimensions
F
*1
2
,
Tolerance class IT16 applies to dimensions in this data sheet unless otherwise specified.
E2EM-X4@@
E2EM-X15@@
Note: 1. The allowable tightening strength depends on the distance from the
Model
M8
M12
M18
M30
Dimensions
21 dia.
F (mm)
17
2. The following strengths assume washers are being used.
42 dia.
edge of the head, as shown in the following table. (A is the distance
from the edge of the head. B includes the nut on the head side. If the
edge of the nut is in part A, the tightening torque for part A applies
instead.)
36
Shielded
M12 × 1
Torque
M30 × 1.5
8.5
4
+0.5
M8
0
33
Toothed washer
Dimension
38
dia.
5
Two clamping nuts
(mm)
2
10
1. 4-dia. vinyl-insulated round cable with 2/3 conductors
2. X1 Models: Operation indicator (red)
9
1. 6-dia. vinyl-insulated round cable with 2/3
2. X1 Models: Operation indicator (red) Setting
Toothed washer
(Conductor cross section: 0.3 mm
Insulator diameter: 1.3 mm), Standard length: 2 m
Setting indicator (green)
X2 Models: Operation indicator (red)
C Models: Operation indicator (yellow)
43
conductors (Conductor cross section: 0.5 mm
Insulator diameter: 1.9 mm), Standard length: 2 m
indicator (green)
X2 Models: Operation indicator (red)
C Models: Operation indicator (yellow)
48
12.5
Two clamping nuts
Part A
Indicator *2
9
M12
+0.5
0
3
10
dia.
180 N·m
Torque
30 N·m
70 N·m
9 N·m
Indicator *2
18.5
12
M18
+0.5
*1
0
dia.
2
,
E2EM
30.5
Torque
12 N·m
Part B
(Unit: mm)
*1
M30
+0.5
0
2
,
dia.
7