E52Q-AM25UAB01 EATON CUTLER HAMMER, E52Q-AM25UAB01 Datasheet - Page 2

• Manufacturer Part Number: E52Q-AM25UAB01
• Description: Inductive Proximity Sensor
• Manufacturer: EATON CUTLER HAMMER

Specifications of E52Q-AM25UAB01

• Sensor Input: Inductive
• Sensing Range: 25 Mm
• Sensing Range Max: 25mm
• Sensor Housing: Cube
• Switch Terminals: Connector
• Sensor Connection: AC Mini, 3-Pin
• Sensor Output: NPN/PNP
• Output Type: 1 N.O.

P51893 Rev 02
MOUNTING CONSIDERATIONS
The sensor should be mounted using two #8 bolts through the
mounting holes provided. (Mounting hardware is not included.)
The sensor can be mounted to any surface without affecting
sensor performance, but it is recommended to use a solid base
to ensure reliable operation.
For all unshielded inductive sensors, ensure there is adaquate
distance between the sensor face any adjacent metals. See the
below diagram for isolation distances.
When E52Q Series sensors are mounted side-by-side, there
is the possibility of interaction between the magnetic fi elds
of the sensors. This could cause unreliable operation. Follow
the limitations noted in the below illustration when mounting
sensors in the same location.
Sensor Isolation Minimum Distances to Adjacent Metals
Sensor-to-Sensor Isolation Minimum Distances
TARGET POSITIONING
To ensure reliable sensing performance, it is recommended to
follow the general guidelines regarding target positioning below.
AUTO-CONFIGURE OUTPUT DETECTION
Available on DC 4-Wire models, Auto-Confi gure outputs
automatically detect how the sensor’s output circuits have been
wired and adjusts to either PNP (sourcing) or NPN (sinking)
without user intervention. This process takes place at sensor
power-up. If the output is changed without power cycling the
sensor, the outputs will not be changed. To ensure your outputs
are correct, always power down the sensor when making a
change to the output confi guration.
Note: If Auto-Confi gure detects one output as NPN, both
outputs will be set to NPN.
Effective: January 2008
Axial (Head On) Approach — The target must be
positioned so that a projection of the target covers at least
half of the sensor’s face. Small targets should be positioned
as close as possible to the origin of the sensing face (where
the crosshairs overlap).
Lateral (Side, Slide-By) Approach — Position the target at
a distance no greater than 75 percent of the models rated
maximum sensing distance.
9 x Sensing Distance
3 x Sensing Distance
3 x Sensing Distance
Questions? Call our Sensor Application Engineers at [phone].
9 x Sensing Distance
WIRING DIAGRAMS
DC Micro Connector
(Models Ending -D01)
(-)
AC Micro Connector
(Models Ending -A01)
L2
APPROXIMATE DIMENSIONS
SPECIFICATIONS
Operating Voltage
Load Current (Max.)
Burden Current
Off-State Leakage
Voltage Drop
Outputs
Standard Target Size (Mild Steel)
Repetition Rate
Repeatability
Hysteresis (Max)
Time Delay Before Availability
Circuit Protection
Operating Temperature
Temperature Drift
Enclosure Rating
Approvals
Indicator LED
1
2
B
C
Auto-Configure enables load
Operating frequency 238 MHz. Conducting radio frequencies at operating frequency and between 2.4 MHz and
3.1 MHz may cause malfunction.
Will operate at -40° C, but range drift will occur.
RD/WH
LOAD
BU
to be wired to +V or (-)
A
WH N.C.
LOAD
2
3
BK N.O.
D
LOAD
3
1
4
1
2
Model
Micro
Connector
Mini
Connector
RD/BK
BN
+V
L1
AC/DC 2-Wire
20-250V AC
20-60V DC
400 mA
< 5 mA
AC Operation:
DC Operation:
< 10V (5V Nominal)
N.O. or N.C. by Model
120 mm x 120 mm
30 Hz
< 3%
15%
300 msec
Short Circuit Protection with Auto-Reset, Reverse Polarity
-25° to +70°C (-13° to +158°F)
±10%
NEMA 4, 4X, 6, 6P, 12 and 13 (IP67 and IP68)
CE
Green: Power
Red: Output
A
(Depth)
40
(1.57)
1
< 2.0 mA Per Output
< 1.5 mA
DC Mini Connector
(Models Ending -E01)
(-)
AC Mini Connector
(Models Ending -B01)
L1
B
(Depth)
40
(1.57)
Auto-Configure enables load
BK
BU
to be wired to +V or (-)
BK N.O.
LOAD
2
1
1
2
3
WH N.C.
C
(Height)
40
(1.57)
LOAD
DC 4-Wire
10-48V DC
300 mA
< 25 mA
NPN Mode: < 400 µA
PNP Mode: < 1 µA
< 2.5V
Complementary
(1N.O. / 1N.C.) with Auto-Confi g
100 Hz
4
3
WH
2
LOAD
BN
D
(Overall Height)
69.2
(2.725)
75.3
(2.97)
+V
L2
Page 2