PTGL07BB220N0B52A0 Murata, PTGL07BB220N0B52A0 Datasheet - Page 76

• Manufacturer Part Number: PTGL07BB220N0B52A0
• Description: POSISTOR, PTC, CIRCUIT PROTECTION
• Manufacturer: Murata
• Series: PTGLr
• Type: PTCr

Specifications of PTGL07BB220N0B52A0

• Thermistor Type: PTC
• Resistance: 22ohm
• Svhc: No SVHC (18-Jun-2010)
• Current Max: 0.5A
• Operating Temperature Max: +85°C
• Operating Voltage: 250V
• Package / Case: Radial
• Resistance Tolerance: ± 30%
• Tolerance: 30 %
• Termination Style: Radial
• Operating Temperature Range: 0 C to + 100 C
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

!Note
• This PDF catalog is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our
• This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
sales representatives or product engineers before ordering.
!Note
This product is designed for application in an
ordinary environment (normal room temperature,
humidity and atmospheric pressure). Do not use under
the following conditions because all these factors
can deteriorate the characteristics or cause product
failure and burn-out.
1. Corrosive gas or deoxidizing gas (Chlorine gas,
Be sure to provide an appropriate fail-safe function
on your product to prevent secondary damage that may be
caused by the abnormal function or the failure of our
product.
To keep solderability of product from declining,
following storage condition is recommended.
1. Storage condition:
2. Storage term:
PTGL Series
When the lead of this product is soldered, pay
attention as follows to avoid the decline of element
characteristics or break-down of the element.
1. Use Rosin type flux or non-activated flux
2. Do not dip the body into flux.
3. Be sure that preheating does not melt the
PTFL/PTFM Series
1. PTFM type is to be screwed beside the Power-
2. If PTFL type is to be mounted with thermal cement,
3. Please bend the lead wire far from the root of the
Hydrogen sulfide gas, Ammonia gas, Sulfuric acid
gas, Nitric oxide gas, etc.)
Temperature -10 to +40 degrees C
Humidity
Use this product within 6 months after delivery
by first-in and first-out stocking system.
(flux should be coated to lead wire only for
soldering.)
soldering of this product.
Transistor on the radiative plate.
the cement should not be of the Cyano Acrylate
family.
body and do not apply force to the lead wire of
the product.
!Caution (Storage and Operating Condition)
!Caution (Other)
Notice (Storage and Operating Condition)
Notice (Soldering and Mounting)
Notice (Soldering and Mounting)
• Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
less than 75%RH (not dewing condition)
2. Volatile or flammable gas
3. Dusty conditions
4. Under vacuum, or under high or low-pressure
5. Wet or humid conditions
6. Places with salt water, oils, chemical liquids or
7. Strong vibrations
8. Other places where similar hazardous conditions
3. Handling after unpacking:
4. Storage place:
4. When the lead of this product is soldered, pay
(1) Use Rosin type flux or non-activated flux.
(2) Do not dip the body into flux.
(3) Be sure that preheating does not melt the
organic solvents
exist
After unpacking, promptly reseal this product or
store it in a sealed container with a drying agent.
Do not store this product in corrosive gas
(sulfuric acid, chlorine, etc.) or in direct
sunlight.
attention as follows to avoid the decline of
element characteristics or break-down of the
element.
(Flux should be coated to lead wire only for
soldering.)
soldering of this product.
!Caution/Notice
R90E.pdf
75
07.3.19
11