KPEG222 Kingstate Electronics Corp., KPEG222 Datasheet - Page 4

• Manufacturer Part Number: KPEG222
• Description: PIEZO ALARM
• Manufacturer: Kingstate Electronics Corp.

Specifications of KPEG222

• Tones: Continuous
• Resonant Frequency: 3.2kHz
• Sound Level Spl: 75dB
• Sound Level Distance: 30cm
• Colour: Black
• Connector Type: 2 Pin
• Current Consumption: 13mA
• Current Rating: 13mA
• Device Type: Alarm
• External: RoHS Compliant

F. MECHANICAL CHARACTERISTICS 機械特性
G. ENVIRONMENT TEST 環境測試
No.
No.
1
2
3
4
1
2
3
4
5
Terminal Mechanical
Temp. cycle test
High temp. test
Low temp. test
相對濕度測試
溫度循環試驗
Soldering Heat
Humidity test
Solderability
焊錫附著性
焊錫耐熱性
Resistance
高溫測試
低溫測試
端子強度
振動測試
Drop test
落下測試
Vibration
Strength
Item
Item
志豐電子股份有限公司 KINGSTATE ELECTRONICS CORP 4/6 KPEG222
After being placed in a chamber at +95℃ for 240 hours
置於+95℃環境中 240 小時
After being placed in a chamber at –40℃ for 240 hours
置於-40℃環境中 240 小時
After being placed in a chamber at +40℃ and 90±5% relative humidity
for 240 hours
置於+40℃, 相對濕度 90±5% 環境中 240 小時
The part shall be subjected to 5 cycles. One cycle shall be consist of：
單體承受溫度循環測試 5 次,其循環內容如圖示：
Lead terminals are immersed in rosin for 5 seconds and then immersed in
solder bath of +270±5℃ for 3±1 seconds.
端子部份浸入松香溶液 5 秒後,再浸入+270±5℃溶融焊鍚槽中 3±1 秒.
距離端子根部1.5mm 的位置,浸入+300±5℃的焊鍚槽3±0.5 秒,或+260±5℃
的焊錫槽 10±1 秒.
The force 10 seconds of 9.8N (1.0kg) is applied to each terminal in axial
direction.
各端子的軸方向施以 9.8N (1.0kg)的力量 10 秒.
Buzzer shall be measured after being applied vibration of amplitude of
1.5mm with 10 to 55hz band of vibration frequency to each of 3
per-pendicular directions for 2 hours.
振動週波數 10∼55HZ、全振幅 1.5mm 於 X.Y.Z 3 個方向,各 2 小時.
The part only shall be dropped from a height of 75cm onto a 40mm thick
wooden board 3 times in 3 axes (X.Y.Z). (a total of 9 times).
單體從 75 公分高處, X.Y.Z.3 個方向,各 3 回,落於 40mm 厚木板上.
Lead terminal are immersed up to 1.5mm from sounder’s body in soilder
bath of +300±5℃ for 3± 0.5 seconds or +260±5℃ for 10±1 seconds.
-40℃
0.5hr 0.5hr 0.25 0.5hr
Test Condition
+25℃
Test Condition
3hours
+95℃
0.5hr
0.5hr 0.25
+25℃
Being placed for 4 hours at
+25℃, buzzer shall be
measured. The value of
oscillation frequency/ current
consumption should be in±10%
compared with initial ones .The
SPL should be in±10dB
compared with initial one.
經測試後, 靜置於+25℃（室溫）
環境中 4 小時後
電流變化量須在±10%內. 輸出音
壓變化量須在±10dB 內.
90% min. lead terminals shall
be wet with solder. (Except
the edge of terminal)
浸入端子部份附著焊鍚 90%
以上.(末端斷面不算)
No interference in operation
操作上無任何不良
No damage and cutting off
端子不鬆動, 不脫落
The value of oscillation
frequency/ current
consumption should be in
10% compared with initial
ones .The SPL should be in ±
10dB compared with initial
one.
諧振頻率與消耗電流變化量須
在±10%內. 輸出音壓變化量
須在±10dB 內.
Evaluation standard
Evaluation standard
,
諧振頻率與消耗