T30UXDC BANNER ENGINEERING, T30UXDC Datasheet - Page 5

• Manufacturer Part Number: T30UXDC
• Description: T30UX Series W/ Discrete Output
• Manufacturer: BANNER ENGINEERING

Specifications of T30UXDC

• Range: 300 Mm To 3 M
• Input: 10 To 30V Dc
• Output: NPN PNP NO NC Selectable
• Body Style: Round
• Range, Measurement: 300 mm to 3 m
• Response Time: 135 ms
• Voltage, Supply: 10-30 VDC
• Accessories Available: Cordsets and Brackets
• Lead Free Status / Rohs Status: RoHS Compliant part

Figure 5. An application for the Auto-Window feature (retroreflective mode)
* Sensor will not Teach or indicate “Teach Not Accepted” when there is no signal present (Signal LED Red or Flashing Red)
Figure 3. Using the Auto-Window feature
Position
Position
Banner Engineering Corp. • Minneapolis, MN U.S.A
Output OFF
Output ON
...
www.bannerengineering.com • Tel: [phone]
Normally Open Operation
Normally Closed Operation
for teaching each output
• P ush and hold
• P osition the target for the
• “ Click” the Discrete
• W ithout moving the
Sensor
Sensor
Output
Output
...
OFF
Discrete push button
for > 2 seconds
center of window
(120 second time out)
...
push button
target, “click” the
Discrete push button
again
ON
Taught Position
Taught Position
Output OFF
Output ON
Procedure
...
Range
Near
D
Output OFF
Output ON
Position
Position
0.04 sec. < “click” < 0.8 sec
D
Push Button
...
Power LED: OFF
Output LED: ON
Signal LED: Must be ON Red or
Power LED: OFF
Output LED: Flashing
Output LED: ON
Output LED: ON or OFF,
Power LED: ON
Output LED: Flashing
Power LED: OFF
...
Any object in this area will switch
the output, whether or not the object
returns a good signal to the sensor.
Sensing Distance
U-GAGE
Output OFF
Teaching the same limit twice automatically centers a window on the
taught position (see figure 4 for window sizes).
General Notes on Teaching
• T he sensor will return to RUN mode if the first TEACH condition is
• T o exit TEACH mode without saving any changes, press and hold the Discrete push button or remote
• A fter the first limit is taught, the sensor will remain in TEACH mode until the TEACH sequence is
Teach Not Accepted
Teach Not Accepted
not registered within 120 seconds after the initial 2 second hold on
Discrete push button.
line > 2 seconds (before teaching the second limit). The sensor will revert to the last saved limits.
finished or exited by a 2 second hold on the Discrete push button or remote line.
Teach Accepted
Teach Accepted
Flashing Red*
.
depending on NO or
NC Mode
Result
or
D
or
Teaching Limits Using the Auto-Window Feature
®
T30UX Series with Discrete Output
(background surface)
Taught Position
Output ON
• N o action required; sensor
• P osition the target for the
• S ingle-pulse the
• W ithout moving
is ready for 1st limit teach
center of window
remote line
the target,
single-pulse
the remote line
again
or
Procedure
0.04 sec. < T < 0.8 sec
T
T
T
T
Remote Line
None
Signal LED: Must be ON Red or
Power LED: OFF
Output LED: Flashing
Output LED: ON
Output LED: ON or OFF,
Power LED: ON
Output LED: Flashing
Power LED: OFF
Teach Not Accepted
Teach Not Accepted
Teach Accepted
Teach Accepted
Figure 4. Window size
T
T
T
T
T
T
.
“A” suffix
“B” suffix
“C” suffix
Flashing Red*
depending on NO or
NC Mode
Result
Models
T
T
T
T
T
T
P/N 138381 rev. B
T
T
T
T
T
T
T
T
T
T
T
T
± 10 mm
± 20 mm
± 30 mm
Window
T
T
5
T
T
T
T
T
T
T
T
T
T