130C-3/4X30FT 3M, 130C-3/4X30FT Datasheet - Page 2

• Manufacturer Part Number: 130C-3/4X30FT
• Description: TAPE, SEALING, RUBBER, BLACK 0.75INX30FT
• Manufacturer: 3M
• Type: Electricalr

Specifications of 130C-3/4X30FT

• Tape Backing Material: Rubber
• Roll Length: 30ft
• Peak Reflow Compatible (260 C): No
• Leaded Process Compatible: No
• Tape Type: Sealing
• Width: 0.75"
• Color: Black
• Elongation: 1000%
• Length, Tape: 30 ft.
• Material, Tape: Rubber
• Temperature Rating: +90 °C
• Thickness, Tape: 0.762 mm
• Width, Tape: 3⁄4 in.
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

Electrical Markets Division
6801 River Place Blvd.
Austin, TX 78726-9000
800-626-8381
Fax [phone]
www.3M.com/electrical
Important Notice
All statements, technical information, and recommendations related to 3M’s products are based on information believed to be
reliable, but the accuracy or completeness is not guaranteed. Before using this product, you must evaluate it and determine if it is
suitable for your intended application. You assume all risks and liability associated with such use. Any statements related to the
product which are not contained in 3M’s current publications, or any contrary statements contained on your purchase order shall
have no force or effect unless expressly agreed upon, in writing, by an authorized officer of 3M.
Warranty; Limited Remedy; Limited Liability.
This product will be free from defects in material and manufacture for a period of one (1) year from the time of purchase. 3M
MAKES NO OTHER WARRANTIES INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY OF MERCHANTABILITY
OR FITNESS FOR A PARTICULAR PURPOSE. If this product is defective within the warranty period stated above, your exclusive
remedy shall be, at 3M’s option, to replace or repair the 3M product or refund the purchase price of the 3M product. Except
where prohibited by law, 3M will not be liable for any indirect, special, incidental or consequential loss or damage arising
from this 3M product, regardless of the legal theory asserted.
Volume Resistivity
(ASTM-D-4325)
Dielectric Constant
(ASTM-D-4325)
Dissipation Factor
(ASTM-D-4325)
* All values are averages and are not intended for
specification purposes.
Specification
Product
The high-voltage corona resistant tape must be
supplied without a liner, be based on ethylene
propylene rubber, and be capable of emergency
operating cable temperature of 130˚C. The tape must
be capable of being applied in either stretched or
unstretched conditions without resulting in loss of
either physical or electrical properties. The tape must
not split, crack, slip, or flag when exposed to various
environments (indoor or outdoor). The tape must be
compatible with all synthetic cable insulations and
have a shelf life of five years.
Engineering/Architectural Specification
Splicing and terminating solid dielectric cable shall
be done in accordance with drawings engineered
by the splice material manufacturer. All splices
and terminations shall be insulated using Scotch
Electrical Tape 130C.
3M and Scotch are trademarks of 3M Company.
Aged 96 hrs. @ 23˚C 96% RH
Original
1200 volts @ 60 Hz
23˚C
90˚C
1200 volts @ 60 Hz
23˚C
90˚C
>10
>10
15
14
ohm-cm
ohm-cm
Recycled paper
40% Pre-consumer waste paper
10% Post-consumer waste paper
0.70%
3.00%
®
3.5
3.6
Installation Technique
This tape should be applied in successive half-lapped
level wound layers until desired build-up is reached.
It should be applied like any rubber tape; that is, the
side of the tape wrapped inside the roll should be
applied outside on the splice (tacky side up). This
will help prevent the roll from getting progressively
further away from the work area.
To eliminate voids in critical areas, highly elongate
130C tape. Stretch tape in critical areas just short
of the breaking point; doing so will not alter its
physical or electrical properties. In less critical areas,
less elongation may be used. The tape should be
stretched to a minimum of 3/4 its original width.
Always attempt to half-lap to produce a uniform
buildup. When using 130C tape for splicing cable
above 15 kV, always highly elongate the tape
throughout the entire splice. Techniques for proper
usage of 130C tape are contained in standard and
special prints available though the “3M System
for Splicing and Terminating” program. These are
available through the local 3M Electrical Products
Division representative.
Shelf Life
The 130C tape has a 5-year shelf life (from date
of manufacture) when stored under the following
recommended storage conditions. Store behind
present stock in a clean dry place at a temperature
of 70˚F (21˚C) and 40% to 50% relative humidity.
Good stock rotation is recommended.
Availability
The 130C tape is available from your electrical
distributor in the following roll sizes.
3/4 in. by 30 ft. (19 mm x 9,1 m)
1 in. by 30 ft. (25,4 mm x 9,1 m)
1 1/2 in. by 30 ft. (38 mm x 9,1 m)
2 in. by 30 ft. (50,8 mm x 9,1 m)
Litho in USA
© 3M 2005 78-8125-9449-3-B