DS9098P-C01+ Maxim Integrated Products, DS9098P-C01+ Datasheet
DS9098P-C01+
Manufacturer Part Number
DS9098P-C01+
Description
IBUTTON RETAINER FOR F5
Manufacturer
Maxim Integrated Products
Series
iButton®r
Datasheet
1.DS9098P-TRL.pdf
(2 pages)
Specifications of DS9098P-C01+
Rohs Information
IButton RoHS Compliance Plan
Card Type
iButton
Number Of Positions
2
Connector Type
Retainer
Insertion, Removal Method
Push In, Pull Out
Mounting Type
Surface Mount
Height Above Board
0.320" (8.11mm)
Contact Finish
Tin
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Features
-
Contact Finish Thickness
-
Mounting Feature
-
Ejector Side
-
19-4875; Rev 8/09
iButton is a registered trademark of Maxim Integrated Products, Inc.
FEATURES
Compact receptacle for F5 iButton
Fully backward-compatible to DS9098
Contacts are stainless steel with selective tin-
Retainer to iButton connection is stainless steel
Withstands up to +250°C for surface mounting
Double redundancy of contacts (2 plus 2)
Contact force exceeds 2N for reliable
Prevents reversed insertion
At insertion, the iButton is latched for retention
The iButton pops up for removal when latch is
Gentle deflection of latches allows removal of
> 25 insertion/withdrawal cycles with no
Compatible with standard pick and place
Cleaning fluids drain freely for quick cleanup
ORDERING INFORMATION
+Denotes a lead(Pb)-free/RoHS-compliant package.
TRL = Tape and reel.
DESCRIPTION
The DS9098P iButton Retainer is a low-cost, surface-mount device to secure an F5 iButton on a printed
circuit board. It consists of three metal pieces (two for ground, one for data) molded into a body of black,
heat-stabilized, glass fiber reinforced liquid crystal polymer. When inserting an iButton into the
DS9098P, closely align axis of the iButton and the retainer. The retainer then latches the flange of the
iButton. At removal, limit deflection of retainer latches to just free the iButton edge from retained state.
Avoid applying excess force to latches.
The DS9098P is only available on tape and reel. The tape specifications match those of 68-lead PLCC
devices except for the deeper pockets and tape-feed sprockets on either side of the 44mm tape. Alignment
pedestals keep the part oriented on tape with the latches adjacent to the sprockets.
www.maxim-ic.com
DS9098P-TRL+
lead plating for optimal solderability to printed
circuit board
to stainless steel
connection
released
the iButton
performance degradation
equipment
PART
Tape and reel, 220 parts per
13in reel
DESCRIPTION
®
mounting
1 of 2
Trace
Data
Copper cladding 0.3 kg/m
soldermask overlay. All dimensions are in millimeters.
Recommended Printed
Outer Ring – Ground
16.50
Circuit Board Layout
19.50
Center – Data
Ø8.0
Top View
Ground Trace
between Pads
Bottom View
19.30
8.5
Ø13.7
iButton Retainer
Ø18.3
2
or 34 µm ( 1oz/sq.ft) with
7 tabs within
+0.10 / -0.00
of datum -A-
Stencil Thickness: 0.15
Stencil Aperture
Latch
Recommended
3-D View
17.60
Ø4.7
Side View
DS9098
8.5
Ø13.8
8.12
Ø18.6
A
Related parts for DS9098P-C01+
DS9098P-C01+ Summary of contents
Page 1
... When inserting an iButton into the DS9098P, closely align axis of the iButton and the retainer. The retainer then latches the flange of the iButton. At removal, limit deflection of retainer latches to just free the iButton edge from retained state. ...
Page 2
... Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are implied. Maxim reserves the right to change the circuitry and specifications without notice at any time © 2009 Maxim Integrated Products DESCRIPTION Maxim is a registered trademark of Maxim Integrated Products, Inc DS9098P PAGES CHANGED ...