FC4A-K2C1 IDEC, FC4A-K2C1 Datasheet - Page 13

• Manufacturer Part Number: FC4A-K2C1
• Description: Analog Output Module
• Manufacturer: IDEC

Specifications of FC4A-K2C1

• Supply Voltage: 24VDC
• No. Of Analog Outputs: 2
• Output Voltage Dc Max: 10V
• External Height: 90mm
• Supply Voltage Min: 20.4V
• Operating Voltage Max: 10V
• Operating Voltage Min: -10V
• External Width: 23.25mm
• External Depth: 70mm
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: MicroSmart CPU Module

Analog Output Specifications
Note 1: Total input system transfer time = Sample repetition time + Internal processing time
When using the FC4A-J4CN1, FC4A-J8C1, or FC4A-J8AT1, the total input system transfer time increases in proportion to the
number of channels used.
Note 2: The data processed in the analog I/O module can be linear-converted to a value between –32768 and 32767. The
optional range designation, and analog I/O data minimum and maximum values can be selected using data registers allo-
cated to analog I/O modules. See page 4-12.
Note 3: When an error is detected, a corresponding error code is stored to a data register allocated to analog I/O operating
status. See page 4-6.
Note 4: The value is measured when a 500V clamp voltage is applied to the power supply and I/O lines.
Category
Type No.
Output Range
Load
DA
Conversion
Output Error
Data
Current Loop Open
Noise
Resistance
Isolation
Effect of Improper Output Connection
Selection of Analog Output Signal Type
Calibration or Verification to Maintain
Rated Accuracy
Load Impedance
Applicable Load Type
Settling Time
Total Output System
Transfer Time
Maximum Error at
25°C
Temperature
Coefficient
Repeatability after
Stabilization Time
Output Voltage Drop
Non-lineality
Output Ripple
Overshoot
Total Error
Digital Resolution
Output Value
of LSB
Data Type in
Application Program
Monotonicity
Maximum Temporary
Deviation during
Electrical Noise Tests
(Note 4)
Recommended Cable
for Noise Immunity
Crosstalk
FC4A M
Voltage
Current
Voltage
Current
ICRO
0 to 10V DC
4 to 20 mA DC
2 kΩ minimum (voltage), 300Ω maximum (current)
Resistive load
50 ms
Settling time + 1 scan time
±0.2% of full scale
±0.015% of full scale/°C
±0.5% of full scale
±1% of full scale
±0.2% of full scale
1 LSB maximum
0%
±1% of full scale
4096 increments (12 bits)
2.5 mV
4 µA
Default: 0 to 4095 (voltage, current)
Optional: –32768 to 32767 (selectable for each channel) (Note 2)
Yes
Not detectable
±3% maximum
Twisted pair shielded cable
No crosstalk because of 1 channel output
Isolated between output and power circuit
Photocoupler-isolated between output and internal circuit
No damage
Using software programming
Impossible
S
FC4A-L03A1
MART
A
NALOG
I/O M
END Refresh Type
130 ms
FC4A-L03AP1
ODULE
U
SER
’
S
M
ANUAL
50 ms
FC4A-K1A1
2: M
ODULE
–10 to +10V DC
1 ms/ch
1 ms × channels
+ 1 scan time
±0.005% of full
scale/°C
±0.1% of full scale
50000 increments
(16 bits)
0.4 mV
0.32 µA
–25000 to 25000
(voltage)
0 to 50000
(current)
Twisted pair cable
2 LSB maximum
S
Ladder Refresh
PECIFICATIONS
FC4A-K2C1
2-7