ELC-PB14NNDT-1 EATON CUTLER HAMMER, ELC-PB14NNDT-1 Datasheet - Page 19

• Manufacturer Part Number: ELC-PB14NNDT-1
• Description: Programmable Logic Controller
• Manufacturer: EATON CUTLER HAMMER

Specifications of ELC-PB14NNDT-1

• Signal Input Type: DC
• Output Type: Transistor
• No. Of Digital Inputs: 8
• No. Of Inputs: 8
• No. Of Outputs: 6
• No. Of Digital Outputs: 6

February 2009
DeviceNet Starter Network
Adapter Product (DSNAP)
Product Description
The Cutler-Hammer
Network Adapter Product (DSNAP)
from Eaton’s electrical business is a
front-mount device that serves as a
single node on DeviceNet, providing
communication capability, control and
monitoring to Intelligent Technologies
(IT.) Electromechanical Starters, as
well as the S751 and S752 Soft Start,
as listed in Tables 50-17 – 50-19.
The IT. DSNAP has an optional HANDS/
OFF/AUTO (HOA) module that enables
the starter to be operated in hand
mode; even if the DSNAP is not pow-
ered. The HOA option is used for cus-
tomers who need the extra security of
manual control in conjunction with the
communication capabilities of
DeviceNet.
Figure 50-18. Typical DSNAP Application
CA08102001E
Catalog Number D77B-DSNAP-X3
with 54 mm IT. Starter
®
DeviceNet Starter
IT. Starter
DSNAP
with
With the addition of a D64 zero
sequence CT, the DSNAP can be
enabled to detect ground faults for
added protection.
Features
■
■
■
■
Comprehensive Motor Data
and Control
■
■
■
■
■
■
■
■
■
Extended Starter Capabilities
■
■
■
■
For more information visit: www.eaton.com
Communication to DeviceNet
consuming one DeviceNet MAC ID.
Manually set MAC ID and baud rate;
configuration using a software
application is not required for
normal operation.
Advanced configuration using
CH Studio.
Includes pre-wired starter inter-
connect cable and terminal adapter.
RMS average current.
% of operating FLA.
% thermal memory.
Integral contact position detection.
Operating status and fault codes.
At speed (soft starters).
START/STOP control.
RUN/FORWARD-REVERSE control.
Trip reset.
Ground fault detection
(with accessory).
Fault log.
Overcurrent warning (adjustable).
Undercurrent warning (adjustable).
PLC, I/O & Communications Products
IT. Connect
Starter Network Adapters (SNAP) (D77B Series) — DeviceNet SNAP
DeviceNet
Table 50-17. IEC SNAP Connectivity
Table 50-18. NEMA SNAP Connectivity
Table 50-19. S751/S752 SNAP Connectivity
Application Description
In a typical application, the DSNAP
front mounts to an IT. starter or soft
start. The DSNAP connects directly to
DeviceNet, allowing for control and
monitoring of the starter/soft start. A
PC or PLC serves as the central control
and scans the DSNAP for motor con-
trol and monitoring information. The
HOA module provides for the ability
to locate operators on the panel for
manual operation.
IEC E101, E501
Frame
105 mm
140 mm
NEMA N101, N501
Size
00
S751/S752 Soft Start
54 mm
45 mm
54 mm
76 mm
0
1
2
3
4
5
Size
B
C
D
E
F
Continuous Ampacity
Rating
135
270
All Sizes
18
27
45
90
9
Continuous
Ampacity
Rating
100 Amp
125 Amp
160 Amp
200 Amp
250 Amp
315 Amp
420 Amp
18 Amp
25 Amp
32 Amp
40 Amp
50 Amp
65 Amp
85 Amp
50-19
50