WLCLG Omron, WLCLG Datasheet - Page 30

• Manufacturer Part Number: WLCLG
• Description: LIMIT SWITCH, ROD
• Manufacturer: Omron

Specifications of WLCLG

• Operating Force Max: 1.39N
• Contact Voltage Ac Max: 500V
• Contact Voltage Dc Max: 250V
• Contact Current Ac Max: 10A
• Contact Current Dc Max: 10A
• Switch Terminals: Screw
• Svhc: No SVHC (15-Dec-2010)
• Actuator Type: Rod

WL
Note: 1. Consult your OMRON representative for the microload WL01j models.
30
WLj-55
WLj-139
WLj-140
WLj-141
WLj-RP40
WLj-RP60
WLj-TC
WLj-TH
WLj-RP
WLj-P1
Models
2. Use the SC Connector for the conduit opening.
3. The actuator can be created using the standard model.
4. The actuator can be created using the standard model. For WL-j141, only WLG2, WLCA2, and WLGCA2 can be used.
Type
Airtight seal
Hermetic seal
(molded terminals
and anti-coolant
models)
Low-temperature
Heat-resistive
Corrosion-proof
Outdoor specifica-
tions
For use in locations
subject to splashes of
water and anti-coolant
Can be used at a tem-
perature of --40_C (The
operating temperature
range is --40_C to
40_C), but cannot with-
stand icing.
Can be used in temper-
atures of 120_C (The
operating temperature
range is 5_C to
120_C).
For use in locations
subject to corrosive
gases and chemicals.
For use in parking lots
and other such outdoor
locations.
Usage
Hermeti-
cally-
sealed
built-in
switch
Uses the W-10FB3-55 Airtight Built-in Switch. (See note 2.)
General-
purpose
built-in
switch
Uses the general-purpose built-in switch.
Silicone rubber is used for rubber parts such as the O-ring,
gasket, etc.
Uses a special built-in switch made from heat-resistant resin.
Silicone rubber is used for rubber parts such as the O-ring,
gasket etc.
Diecast parts such as the switch box are made of corrosion-
proof aluminum.
Rubber sealing parts are made of fluorine rubber which aids in
resisting oil, chemicals and adverse weather conditions.
Exposed nuts and screws (except the actuator section) are
made of stainless steel.
Moving and rotary parts such as rollers are made of sintered
stainless steel or stainless steel.
Rubber parts are made from silicone rubber, which has a high-
tolerance to deterioration over time, and changes in tempera-
ture.
Rollers are made of stainless steel to improve corrosion resist-
ance.
Exposed nuts and screws are made of stainless steel.
Environment-resistant construction
Connection lead wires:
Standard 5-m VCT (vi-
nyl cabtire cable) cable
attached. Finished di-
ameter: 11.5 mm,
4-core.
Connection lead wires:
Standard 5-m VCT
cable, with high flexibil-
ity and good anti-oil
properties attached.
p p
Finished diamete
Finished diameter:
11.5 mm, 4-core.
The case cover and
conduit opening are
molded from epoxy
resin. The cover cannot
be removed.
The case cover, cover
box and conduit open-
ing are molded from
epoxy resin. The cover
cannot be removed
(140 141 RP40 and
(140, 141, RP40, and
RP60).
The Head opening is
protected from cutting
powder. (WLj-141)
The connector can be
removed, so it is pos-
sible to use flexible
wires in the cable.
Rubber parts are made
from fluorine rubber.
All models except the
low-temperature and
heat-resistive models.
(See note 3.)
All models except the
low-temperature and
heat-resistive models.
(See note 4.)
All models except air-
tight, hermetic, heat-re-
sistive, corrosion-proof,
or lamp-equipped mo-
dels.
All models except air-
tight, hermetic, low-
temperature, corrosion-
proof, lamp-equipped,
nylon roller
(WLCA2-26N), seal
roller models, and resin
rod (WLNJ-2) models.
All models except over-
travel model (-2N), fork
lever lock models
(WLCA32-41 to -43),
low-temperature, heat-
resistive, and lamp-
equipped models.
Only the general-pur-
pose overtravel models
(WLH2/12), the over-
travel high-sensitivity
models (WLG2/12) and
some standard models
(e.g., WLCA2) can be
used. Excluding heat-
resistive models.
Appropriate
models
WL