VCM10000 Red Lion Controls, VCM10000 Datasheet - Page 2

• Manufacturer Part Number: VCM10000
• Description: 4-50 V
• Manufacturer: Red Lion Controls
• Type: Signal Converterr

Specifications of VCM10000

• Rohs Compliant: YES
• Input Type: 4 to 50 V AC/DC, 50/60Hz.
• Module Type: Voltage Converter
• Mounting Type: Self-Stick Pad
• Output Type: Solid State DC Contact Closure, 30 VDC at 100 mA
• Termination: 6" Leads
• Lead Free Status / Rohs Status: RoHS Compliant part

TCM - TRIAC CONVERTER MODULE
operate with photo-electric sensors and programmable controllers that have 115
VAC Triac outputs. Due to protective suppression circuits connected in parallel
with Triacs, these outputs have a high OFF-State Leakage current, which, if
unloaded, is sufficient to keep a VCM in the ON condition continuously.
up to 4 mA and allows the application of RLC Counters to most unloaded
Triac outputs. These modules are available for operation with 115 VAC ±10%
50/60 Hz only. They operate at count rates up to 10 cps, and also provide
input/output electrical isolation. Connections for the TCM are the same as
those for the VCM.
Note: VCM’s can be used with Triac outputs that are also driving substantial
TYPICAL CONNECTION EXAMPLE FOR VCM & TCM
(Shown with optional VCM for Control Voltage Remote Reset)
instruction literature for wiring. Reference switch and contact input information
LCM - CONVERTER MODULE
output, and to any count signal voltage from +3 to +28 VDC. The module
accepts input count pulses from NPN Open-Collector Transistor outputs, Bi-
Polar outputs, or sourcing outputs such as Emitter-Follower or PNP Open-
Collector Transistors (Sourcing outputs must be externally loaded with a load of
10 Kohms or less). The LCM output is a Bi-Polar drive that is compatible with
either the Low-Speed or High-Speed Counter inputs as well as the Remote
Reset input** of the CUB Counters. The output is inverted with respect to the
input which causes the CUB Counter to increment on the leading (positive
going) edge of a count pulse. Power for operation of the LCM can be normally
obtained from the existing D.C. power supply used to operate the sensor or other
logic circuitry. When count pulse signals are generated by switch contacts the
LCM output can be applied to the L.S. input of the CUB to de-bounce these
pulses. Minimum pulse width when driving the L.S. input is 10 msec and
maximum count rate is 50 cps.
*
** When used to operate Remote Reset input, the LCM will reset counter when
The TCM is a specialized version of the VCM. It is specifically designed to
The TCM incorporates a current bias that offsets output leakage currents
loads, since the load will shunt the leakage current away from the VCM input.
Consult Connections and Configurations set up information in counter
The LCM adapts CUB* Counters to practically any type of logic and sensor
input to LCM goes high due to signal inversion.
LCM intended for use with CUB1,2,3,and 7.
2
SPECIFICATIONS
1. INPUT: 115 VAC ± 10% (50/60 Hz) at 5mA min
2. FREQUENCY: 10 HZ max output
3. OUTPUT: Solid state DC contact closure
4. ENVIRONMENT: 0-50º C
1. POWER: 5 to 28 VDC, 8 mA max
2. INPUT: V
3. OUTPUT: Bipolar 3 VDC with 1 mA sink/source (output should not be
4. FREQUENCY: MAX input/output frequency = 50 Khz (see counter input
5. ENVIRONMENT: 0-50º C
SPECIFICATIONS
connected to voltage levels above 3.5 VDC)
for frequency limitations)
Output rating: 30 VDC at 100mA
Output Isolation: 2300 VRMS
Off State Leakage: 1µA max
V
IL
IH
= +1.0 VDC, 50 µA max sink
= +2.5 to 28 VDC, 500 µA max source