DPM 40 LASCAR, DPM 40 Datasheet

DPM 40

Manufacturer Part Number

DPM 40

Description

DPM, LED, 3.5DIGIT

Manufacturer

LASCAR

Datasheets

1.DPM_40.pdf (4 pages)

2.DPM_40.pdf (2 pages)

Specifications of DPM 40

Supply Voltage Range

4.5V To 5.5V

Backlighting Colour

Red

No. Of Digits / Alpha

3.5

Display Size

48mm X 20mm

Panel Cutout Height

68mm

Panel Cutout Width

33mm

Operating Temperature Range

0Â°C To +50Â°C

Svhc

Rohs Compliant

Yes

Backlighting Color

Red

Lead Free Status / RoHS Status

Lead free / RoHS Compliant

Current page: 1 of 2
Download datasheet (87Kb)

DPM 40

SAFETY

To comply with the Low Voltage Directive (LVD 93/68/EEC), input voltages to the module’s pins must not exceed 60Vdc. If

voltages to the measuring inputs do exceed 60Vdc, then fit scaling resistors externally to the module. The user must ensure

that the incorporation of the DPM into the user’s equipment conforms to the relevant sections of BS EN 61010 (Safety

Requirements for Electrical Equipment for Measuring, Control and Laboratory Use).

A compact meter ideally suited to applications where excellent readability under all lighting conditions is required. The

meter is fitted with high efficiency LEDs which, together with the integral red filter, give a high contrast display with 11mm /

0.43" digit height. The meter can be easily scaled by the user to indicate volts, amps or other engineering units and may be

used in single-ended, differential or floating input modes.

SCALING

Two resistors Ra and Rb may be fitted in order to

alter the full scale reading (F.S.R.) of the meter - see

table.

The meter will need re-calibration by adjusting the

calibration potentiometer.

NOTE

Ensure that solder link La across Ra is OPEN.

Required F.S.R.

20V

200V

2kV

200 A

2mA

20mA

200mA

DIMENSIONS

11mm (0.43“) Digit Height

Programmable Decimal Points

Auto-zero

Auto-polarity

200mV d.c. Full Scale Reading (F.S.R.)

Panel cut-out 68 x 33 (2.68 x 1.30)

Note

All dimensions in mm (inches)

910k

LINK

46.1 (1.81)

72.0mm

100R

100k

10R

10k

www.lascarelectronics.com

9.0 (0.35)

Specification

Accuracy (overall error) *

Linearity

Sample rate

Operating temperature range

Warm-up time

Temperature s

Supply

Input leakage current (Vin = 0V)

* To ensure maximum accuracy, re-calibrate periodically.

Standard Meter

voltage (V+ to V-)

current

1.6 (0.06)

10.0 (0.39)

3.7 (0.15)

tability

3 (0.12) dia

9.75 (0.38)

23.65 (0.93)

FRONT VIEW

Min.

30.25 (1.19)

4.5

Typ.

150

0.1

2.5

62.0 (2.44)

67.5 (2.66)

48.0 (1.89)

2.54 (0.1) pin pitch

½ Digit LED Module

2.54 (0.1) pin pitch

Max.

±1

5.5

Stock Number

DPM 40

REAR VIEW

% (±1 count)

samples/sec

9.75 (0.38)

ppm/°C

minute

count

Unit

°C

5.25

(0.21)

Related parts for DPM 40

DPM 40 Summary of contents

Page 1

... Supply current Input leakage current (Vin = 0V ensure maximum accuracy, re-calibrate periodically. 3 (0.12) dia 9.0 (0.35) 1.6 (0.06) 10.0 (0.39) 3.7 (0.15) www.lascarelectronics.com ½ Digit LED Module 3 Stock Number DPM 40 Min. Typ. Max. Unit 0.1 % (±1 count) ±1 count 2.5 samples/sec 0 50 ° ...

Page 2

... SHORTED Cut to Solder to OPEN SHORT + DP1 + DP2 DP3 E DP COM Operation with input referenced to panel meter supply 220k 6R2 SET ZERO 2 COM OUT 0V Measuring 4-20mA to read 0-999. Meter power supply must be isolated from 4-20mA current loop. S.L. Applies to DPM 40/7 ...

Related keywords

DPM 40 datasheet
DPM 40 data sheet
DPM 40 pdf datasheet
DPM 40 component
DPM 40 part
DPM 40 distributor
DPM 40 RoHS
DPM 40 datasheet download