6-Y-1-2-RMF-PM-115A EATON CUTLER HAMMER, 6-Y-1-2-RMF-PM-115A Datasheet - Page 96

• Manufacturer Part Number: 6-Y-1-2-RMF-PM-115A
• Description: Electromechanical Totalizing Counter
• Manufacturer: EATON CUTLER HAMMER

Specifications of 6-Y-1-2-RMF-PM-115A

• No. Of Digits / Alpha: 6
• Digit Height: 4.8mm
• Power Consumption: 7W
• Mounting Type: Panel
• Peak Reflow Compatible (260 C): No
• Leaded Process Compatible: No
• Counter Supply Voltage: 115VAC
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant

54
54
54
54
54
54
54
54
54
54
54
54
54
54
54
54
54
54
54
54
54
54
54
54
54
54
54
54
54
54
54.4
General Specifications, continued
Description
Signal Input, continued
5A AC models (5770X-44X)
Process models (5770X-45X)
Optional Outputs
Relay board
Analog retransmission
RS-485 serial communication
Environmental
Operating environment
Temperature
Humidity
Vibration
Shock
EMC/EMI
Front panel
Agency approval
Pollution degree 2
96
Range
Frequency
Impedance
Overrange
Accuracy
Range
Impedance
Overrange
Power output
Accuracy
Dual relay
Contact rating
Isolation dielectric strength
Output signals
Accuracy
Isolation dielectric strength
Baud rate
Parity
Address range
Protocol
Isolation dielectric strength
Operating
Storage
Control Products Catalog CA08102001E—August 2010 www.eaton.com
Counters, Panel Meters, Tachometers and Timers
Digital Panel Meters
Specification
5A AC, true rms
40 to 1000 Hz
0.02 ohm (shunt output capacitive coupled)
10A maximum
±0.4% of reading, ±0.13% FS, ±0.5 digit, and ±200 PPM/°C for crest factor = 1; plus ±0.7%
for crest factor = 1 to 3; and ±2.5% for crest factor = 5
4–20 mA DC, 0–10 Vdc, 1–5 Vdc; separate input terminals for voltage and current signals
100 ohms (current input) and 1.27 mohms (voltage input)
50 mA maximum (current input) and 100V maximum (voltage input)
24 Vdc ±10%, 90 mA max, short-circuit protected
±0.1% of reading, ±0.03% FS, ±0.5 digit, and ±80 PPM/°C
1 set of Form C contacts each
5A, 250 Vac or 30 Vdc
2300 Vac
4–20 mA (<750 ohms) and 0–10V (>2500 ohms)
0.13% FS, 100 PPM/°C, 0.07% FS change with 4–20 mA load, ±0.3% FS for 4–20 mA
output, only after exposure to 85% relative humidity
2300 Vac to signal inputs, relays and AC power input; 500 Vac to RS-485 and DC power
inputs
1200, 2400, 4800, 9600 or 19,200, programmable
Even, odd or no parity
00 to 99 decimal
Opto 22
2300 Vac to signal inputs, relays, and AC power input; 500 Vac to analog outputs and DC
power inputs
Indoor use to 2000 meters
32 to 122°F (0 to 50°C)
–4 to 158°F (–20 to 70°C)
0 to 85% RH, non-condensing
2.5 Gs, 30 to 200 Hz
30 Gs, 11 ms half sinewave
Per EN 61326-1 industrial
NEMA 4X when mounted with gasket provided
CE EMC immunity and emissions requirements were met using shielded wiring on the
RS-485, analog output and signal input lines. The shields were connected to earth ground
at the Eclipse end of the shields.
Conducted emissions requirements were met assuming that the AC signal input would not
be connected directly to the AC mains.
The measurement error during RF immunity testing was less than ±5% of full scale.
In addition, models with an AC signal input had measurement error of less than +25% of
full scale during RF immunity testing of the RS-485 at frequencies below 1 MHz.
Overvoltage Category II
®
compatible