ELC-EX08NNDT-1 EATON CUTLER HAMMER, ELC-EX08NNDT-1 Datasheet - Page 21
![Programmable Logic Controller](/photos/21/26/212677/4551006_sml.jpg)
ELC-EX08NNDT-1
Manufacturer Part Number
ELC-EX08NNDT-1
Description
Programmable Logic Controller
Manufacturer
EATON CUTLER HAMMER
Datasheet
1.ELC-EX06NNNI-2.pdf
(34 pages)
Specifications of ELC-EX08NNDT-1
Signal Input Type
DC
Output Type
Transistor
No. Of Inputs
4
No. Of Outputs
4
For Use With
Eaton ELC Controllers
February 2009
QCPort Starter Network
Adapter Product (QSNAP)
Product Description
The Cutler-Hammer QCPort Starter
Network Adapter Product (QSNAP)
from Eaton’s electrical business is a
front-mount device providing commu-
nication capability, control and moni-
toring to Intelligent Technologies (IT.)
Electromechanical Starters, as well as
the S751 and S752 Soft Start, as listed
in Tables 50-24 – 50-26. The QSNAP
allows connection to any communica-
tions adapter and provides access to
any support network.
The IT. QSNAP has an optional
HANDS/OFF/AUTO (HOA) module
that enables the starter to be operated
in hand mode; even if the QSNAP is
not powered. The HOA option is
Figure 50-20. Typical QSNAP Application
CA08102001E
Catalog Number D77B-QSNAP-X1
with 54 mm IT. Starter
To Control
PC or PLC
D77D-DNA, D77D-PNA
D77D-EIP, D77D-EMA,
used for customers who need the
extra security of manual control in
conjunction with industrial network
communication capabilities.
With the addition of a D64 zero
sequence CT, the QSNAP can be
enabled to detect ground faults for
added protection.
Features
■
■
■
Comprehensive Motor Data
and Control
■
■
■
■
■
■
■
■
■
Extended Starter Capabilities
■
■
■
■
■
For more information visit: www.eaton.com
Configuration using a software
application is not required for
normal operation.
Advanced configuration using
CH Studio.
Includes pre-wired starter inter-
connect cable and terminal adapter
RMS average current.
% of operating FLA.
% thermal memory.
Integral contact position detection.
Operating status and fault codes.
At speed (soft starters).
START/STOP control.
RUN/FORWARD-REVERSE control.
Trip reset.
Ground fault detection
(with accessory).
Fault log
Overcurrent warning (adjustable).
Undercurrent warning (adjustable).
Emergency stop detection.
IT. Starters with QSNAPs
PLC, I/O & Communications Products
IT. Connect
Starter Network Adapters (SNAP) (D77B Series) — QCPort SNAP
Table 50-24. IEC SNAP Connectivity
Table 50-25. NEMA SNAP Connectivity
Table 50-26. S751/S752 SNAP Connectivity
Application Description
A typical application may contain
many QSNAPs connected to a single
network adapter. With this architec-
ture, an entire panel can be repre-
sented by a single network adapter.
IEC E101, E501
Frame
105 mm
140 mm
NEMA N101, N501
Size
00
S751/S752 Soft Start
54 mm
45 mm
54 mm
76 mm
0
1
2
3
4
5
Size
B
C
D
E
F
Continuous Ampacity
Rating
135
270
All Sizes
18
27
45
90
9
Continuous
Ampacity
Rating
100 Amp
125 Amp
160 Amp
200 Amp
250 Amp
315 Amp
420 Amp
18 Amp
25 Amp
32 Amp
40 Amp
50 Amp
65 Amp
85 Amp
50-21
50