3C0000407 CAL CONTROLS, 3C0000407 Datasheet - Page 4

• Manufacturer Part Number: 3C0000407
• Description: COMMUNICATION BOARD, RS485
• Manufacturer: CAL CONTROLS

Specifications of 3C0000407

• Accessory Type: Communication Board
• Communication Option: RS485 Modbus Protocol
• Power Connection Type: CALCOMMS 128 CAL Controll
• For Use With: 9500P Programmable Temperature And Process Controller

Thermocouple
9 types:
Standards:
CJC rejection:
External resistance:
Resistance thermometer
RTD/Pt100
Standards:
Bulb current:
Analogue process inputs
Applicable to all Thermocouple and RTD inputs (SM =sensor maximum)
Calibration accuracy:
Sampling frequency:
Common mode rejection:
Series mode rejection:
Temperature coefficient:
Reference conditions:
Output devices (check configuration)
SSd1 and SSd2:
Relay 1,2,3
Analogue output:
General
Displays:
Keypad:
Programmer functions:
Segments:
Programs:
Program memory:
Environmental
Humidity:
Altitude:
Installation:
Pollution:
Protection:
EMC emission:
EMC immunity:
Ambient:
Mouldings:
Weight:
Safety:
Dimensions
Front facia:
Sleeve length:
Instrument body:
Overall length:
Supply Voltage:
Power Requirements:
CAL 9500P Specifications
B, E, J, K, L, N, R, S, T
IEC 584–1–1 : EN60584–1
20:1 (0.05°/°C) typical
100
2 or 3 wire
IEC751: EN60751 (100
0.2mA maximum
0 to 50mV, +/- 0.1%. 0-20mA, 4-20mA, +/- 0.1%. 0-5V, +/- 0.1%. 0-10V, +/- 0.1%
+/- 0.25%SM +/- 1°C
input 10Hz, CJC 2 sec.
Negligible effect up to 140dB, 240V, 50-60Hz
60dB, 50-60Hz
50ppm/°C SM typical
22°C +/- 2°C, rated voltage after 15 minutes settling time.
Solid state relay driver: To switch a remote SSR 6Vdc (nominal) 20mA non-isolated
Miniature power relay: Form A/SPST contacts (AgCdO): 2A/250Vac resistive load
4–20mA 500Ω max +/- 0.1% full scale typical
0–5Vdc 10mA (500Ω min) +/- 0.1% full scale typical
0–10Vdc 10mA (1KΩ min) +/- 0.1% full scale typical
Upper, 4 Digits, high brightness green LED. 10mm (0.4”) high.
Lower, 4 Digits, high brightness orange LED 9mm (0.35”) high.
Digital range -199 to 9999. Hi-res mode -199.9 to 999.9.
LED output indicators - SP1 square, green; SP2/SP3 round, red
3 elastomeric buttons
Total of 126 per program
Maximum of 31 programs
351 Bytes (see memory allocation table)
Max 95% non-condensing
up to 2000M
Categories ll and lll
Degree ll
NEMA 4X, lP66 (Front panel only)
EN50081-1 FCC Rules 15 subpart J Class A
EN50082-2
0-50ºC (32-130°F)
flame retardant polycarbonate
180g (6.4 oz)
EN61010–/CSA22.2 No 1010.1 92 (see users manual)
51.0 x 51.0mm (2.0” x 2.0”) (includes gasket)
106.7mm (4.2”) (with gasket fitted)
44.8 x 44.8mm (1.76” x 1.76”)
116.2mm (4.57”)
100–240Vac, 50–60Hz +/- 10% maximum permitted fluctuation
6.0VA (nominal)
www.cal-controls.com
maximum
0°C/138.5
Visit our website for - pdf technical manuals, application notes, tutorials and much more
100°C Pt)
includes
Typical Application
In this example the load temperature is monitored by a
temperature transducer/transmitter which provides a
4–20mA input signal to the controller. The 4–20mA output
has been allocated to SP1 to drive an SCR power
controller providing a phase angle controlled output to
the heater.
F1 Fuse:
F2 Fuse:
S1 Switch:
Model 9500P
(48x48mm) 1/16 DIN
gasket
(2.0)
51.0
includes gasket
1A time lag type to IEC127. CSA/UL rating
250Vac
High Rupture Capacity (HRC) Suitable for
maximum rated load current
IEC/CSA/UL Approved disconnecting device.
51.0 (2.0)
Dimensions in mm (inches)
116.2
(4.57)
www.cal-controls.com
Technical Specifications
with gasket fitted
106.7 (4.2)
(1.76)
44.8
Transducer
4–20mA
Mains
(1.76)
44.8
L
N
9500P with COMMS board fitted
(+)
S1
controller
Analogue
4–20mA
17 18
power
Model
1
INPUT
(–)
2
(–)
19
9 5 B 1 1 P B – – –
3
(+)
20
4
F1
F2
Heater
User configurable
21 22
5
6
alarms
23 24
L
7
N
8