T1611100 Red Lion Controls, T1611100 Datasheet - Page 19

• Manufacturer Part Number: T1611100
• Description: PID TEMPERATURE CONTROLLER, 3RELAYS
• Manufacturer: Red Lion Controls
• Type: Temperaturer

Specifications of T1611100

• Thermocouple Type: T, E, J, K, R, S, B, N, C, Linear MV
• Operating Temperature Max: 50°C
• Operating Temperature Min: 0°C
• Output Voltage Max: 250VAC
• Output Voltage Min: 30VDC
• Accuracy: 0.3%
• Approval: RoHS Compliant
• Brand/series: T16 Series
• Contact Form: SPST
• Dimensions: 49.5mmW×49.5mmH×115.3mmD
• Enclosure Rating: IP65
• Input Type: RTD/Thermocouple
• Ip Rating: IP65
• Memory: EEPROM
• Mounting Type: Panel
• Output Type: Relay
• Power, Rating: 8 VA
• Primary Type: Controller
• Special Features: EEPROM
• Standards: cURus, CE
• Termination: Screw
• Voltage, Supply: 85 to 250 VAC
• Lead Free Status / Rohs Status: RoHS Compliant part

recommended every two years by qualified technicians using appropriate
equipment. Calibration may be performed by using the front panel or with the
TP16KIT. The front panel method is explained below. (Refer to the TP16KIT
bulletin for calibration instructions using TP16KIT cable and software.)
exiting Factory Service Module 9-FS. In this case, the existing calibration
settings remain in effect.
the manufacturer’s warm-up recommendations for the calibration source or
measuring device.
Millivolt Calibration (T16)
0.03% (or better) connected to terminals 8 (comm.) and 9 (+). When calibrating
the input, the millivolt calibration must be performed first, then the Cold Junction
or RTD Resistance.
7.5 MODULE 9 F
Cold Junction (T16)
types T, E, J, K, C or N (connected to terminals 8 and 9) and a calibrated
external reference thermocouple probe measuring in °C with resolution to
tenths. The two probes should be brought in contact with each other or in some
way held at the same temperature. They should be shielded from air movement
and allowed sufficient time to equalize in temperature. (As an alternative, the
T16 thermocouple may be placed in a calibration bath of known temperature.)
If performing the millivolt calibration prior, verify that the correct input type is
configured in Input Module 1-IN before performing the following procedure.
(After the millivolt calibration the controller will default to type J.) If using RTD
only, the cold junction calibration need not be performed.
[CodE]
PROMPT
[CAL]
[CJC]
CodE
The controller is fully calibrated from the factory. Recalibration is
Calibration may be aborted by disconnecting power to the controller before
Note: Allow the controller to warm up for 30 minutes minimum and follow
Millivolt calibration requires a precision voltage source with an accuracy of
[CodE]
[StP1]
[StP2]
[StP3]
[StP4]
[StP5]
Cold Junction calibration requires a thermocouple of known accuracy of
PROMPT
[CAL]
48
Top display to
external
reference
14.0 mV
28.0 mV
42.0 mV
56.0 mV
0.0 mV
COMPARE
APPLY
Press $ until
Press # for
After 5 seconds (minimum), press ".
After 5 seconds (minimum), press ".
After 5 seconds (minimum), press ".
After 5 seconds (minimum), press ".
After 5 seconds (minimum), press ".
CALIBRATION
Press $ until
Press ".
Press # for
Press # or $ to adjust the
bottom display until the top
process display matches the
external reference then press ".
FRONT PANEL ACTION
FRONT PANEL ACTION
YES
48
, press ".
YES
, press ".
48
ACTORY
, press ".
, press ".
PARAMETER MENU
S
ERVICE
19
O
Input Calibration (P16)
0.03% (or better) that is capable of generating 10.0 V connected to terminals 8
(COMM) and 9 (+10V) and 20.00 mA connected to terminals 8 (COMM) and
10 (20mA). The current calibration can be skipped by pressing " at the not
applicable prompts if using the controller for process voltage only.
RTD Resistance (T16)
0.1
jumper between 9 and 8 at StP1 and the 277.0 ohm resistor between 9 and 8 at
StP2. If using thermocouple only, the RTD calibration need not be performed.
[CodE]
[StP1]
[StP2]
[CodE]
[StP1]
[StP2]
[StP3]
[StP4]
[StP5]
[StPA]
[StPb]
PROMPT
PROMPT
PERATIONS
[CAL]
[CJC]
[rtd]
[CAL]
Process calibration requires a precision signal source with an accuracy of
RTD calibration requires a precision 277.0 ohm resistor with an accuracy of
(or better). Connect a jumper between terminals 9 and 10 with a 0 ohm
277.0 ohm
0.0 ohm
20.0 mA
0.0 mA
APPLY
10.0 V
APPLY
0.0 V
2.5 V
5.0 V
7.5 V
Press $ until
Press ".
Press ".
Press # for
After 5 seconds (minimum), press ".
After 5 seconds (minimum), press ".
Press $ until
Press # for
After 5 seconds (minimum), press ".
After 5 seconds (minimum), press ".
After 5 seconds (minimum), press ".
After 5 seconds (minimum), press ".
After 5 seconds (minimum), press ".
After 5 seconds (minimum), press ".
After 5 seconds (minimum), press ".
(.%! ! 3)
FRONT PANEL ACTION
FRONT PANEL ACTION
YES
YES
48
48
, press ".
, press ".
, press ".
, press ".