UNR-3.3/8-D5T-C Murata Power Solutions Inc, UNR-3.3/8-D5T-C Datasheet - Page 3
![DC/DC TH 8A 5-3.3V Non-Iso](/photos/17/94/179471/unr18-33w_sml.jpg)
UNR-3.3/8-D5T-C
Manufacturer Part Number
UNR-3.3/8-D5T-C
Description
DC/DC TH 8A 5-3.3V Non-Iso
Manufacturer
Murata Power Solutions Inc
Series
UNRr
Datasheet
1.UNR-3.38-D12-C.pdf
(10 pages)
Specifications of UNR-3.3/8-D5T-C
Product
Non-Isolated / POL
Output Power
26 W
Input Voltage Range
4.75 V to 5.5 V
Number Of Outputs
1
Output Voltage (channel 1)
3.3 V
Output Current (channel 1)
8 A
Lead Free Status / Rohs Status
Lead free / RoHS Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
UNR-3.3/8-D5T-C
Manufacturer:
DATEL
Quantity:
334
Part Number:
UNR-3.3/8-D5T-C
Manufacturer:
MURATA/村田
Quantity:
20 000
www.murata-ps.com
Performance/Functional Specifications
Typical @ T
Input Voltage Range
Input Current:
On/Off Control:
Efficiency
Overcurrent Protection:
Start-Up Time:
Switching Frequency
Storage Temperature
Input Ripple Current:
Input Filter Type
Overvoltage Protection
Reverse-Polarity Protection
V
V
Temperature Coefficient
Ripple/Noise (20MHz BW)
Line/Load Regulation
Transient Response (50-100% load):
Operating Temperature (Ambient):
Dimensions:
OUT
OUT
D5 Models
D12 Models
Normal Operating Conditions
Standby/Off Mode
1.8/2.5V Models
3.3/8 -D5 Models
3.3/10 -D5 Models
3.3/8 -D12 Models
3/3/10 -D12 Models
1.8V
2.5/3.3V
Trim pin tied to +Output:
1.8V
1.8/2.5V
3.3V
3.3/8 -D12 Models
3.3/10 -D12 Models
V
On/Off to V
D5 Through-Hole Models
D5 Surface-Mount Models
D12 Through-Hole Models
D12 Surface-Mount Models
Flammability
Without Derating
With Derating
Functionality
Logic Threshold
Trim pin tied to Output Return
Technique
Overcurrent Detection Point
Average Short Circuit Current:
IN
Trim Range
D5 Models
D12 Models
to V
Accuracy (50% load):
OUT
OUT
OUT
A
= +25°C under nominal line voltage and full-load conditions unless noted.
OUT
Models
Models
-D5 Models
OUT
OUT
OUT
Models
Models
Dynamic Characteristics
Environmental
Physical
Input
Output
3.0 to 3.6 Volts (3.3V nominal)
4.75-5.5 Volts (5V nominal)
10.8-13.6 Volts (12V nominal)
See Ordering Guide
3.6mA typical
150mAp-p
100mAp-p
150mAp-p
110mAp-p
250mAp-p
Capacitive
None
None
±2% of V
±1% of V
V
V
±0.02% per °C
See Ordering Guide
See Ordering Guide
See Ordering Guide
100μsec to 3% of final value
25μsec to 2.5% of final value
50μsec to 2.5% of final value
50μsec to 1% of final value
50μsec to 2.5% of final value
25/30msec (1.8/2.5V
25/30msec (1.8/2.5V
300kHz (±30kHz)
See Derating Curves
to +100°C (See Derating Curves)
2" x 1" x 0.39" (51 x 25 x 9.9mm)
2" x 1" x 0.43" (51 x 25 x 10.9mm)
2" x 1" x 0.48" (51 x 25 x 12.2mm)
2" x 1" x TBD" (51 x 25 x 12.7mm)
94V-0
1 Amp typical, 3 Amps maximum
4 Amp typical, 6 Amps maximum
–40 to +105°C
TTL high (or open) = on, low = off
+0.8-2.0 Volts (1.5V typical)
"Hiccup" with auto-recovery
110-180% of rated current
OUT
OUT
= 1.52 Volts or less
= 3.6 Volts or greater
OUT
OUT
maximum
maximum
OUT
OUT
models)
models)
Return Current Paths
These are non-isolated DC/DC converters. The Input Return, Output Return
and Logic Ground pins are all connected together internally. To the extent
possible, all input and load currents should be returned through the Input
Return and Output Return, respectively (via low-impedance runs). Any con-
trol signals applied to the On/Off Control pin should be referenced to Logic
Ground. The internal trace leading to Logic Ground is not designed to carry
high current. Consequently, devices should never be installed in a manner
that results in high current flow through Logic Ground (i.e., the Input/Output
Return pins should never be left open or connected via high-impedance paths).
I/O Filtering and Noise Reduction
All UNR 18-33W Series converters are tested and specified with external
470μF input capacitors (20m ESR, 6Arms ripple-current rating) and
external 22μF output capacitors (200m ESR). External input capacitance is
required and must be rated to handle the input ripple current as follows:
In critical applications, input/output ripple/noise may be further reduced by
installing additional I/O caps.
Shielding
Case Connection
Case Material
Pin Material
Input Voltage:
Input Reverse-Polarity Protection
Input/Output Overvoltage Protection
Output Current
Storage Temperature
Lead Temperature (Soldering, 10 sec.)
These are stress ratings. Exposure of devices to any of these conditions may adversely
affect long-term reliability. Proper operation under conditions other than those listed in the
Performance/Functional Specifications Table is not implied.
T E C H N I C A L N O T E S
All models are tested and specified with an external 470μF input capacitor with a 20m
ESR and a 6Arms ripple-current rating, as well as a 22μF output capacitor with a 200m ESR.
See I/O Filtering and Noise Reduction for more details. These devices have no minimum-load
requirements and will regulate under no-load conditions. Listed specifications apply for both
"T" and "SM" models as appropriate.
See Output Overcurrent Detection for details.
See On/Off Control for details.
See Output Voltage Trimming for details.
For all models, output noise can be further reduced with the installation of additional
external output capacitors. See I/O Filtering and Noise Reduction for details.
See Start-Up Time for details.
See Temperature Derating for details.
Single Output, Non-Isolated, 5 or 12V
Continuous:
Transient (100msec)
D5 Models
D12 Models
I
RMS
Technical enquiries email: sales@murata-ps.com, tel:
= I
OUT
Absolute Maximum Ratings
UNR D5/D12 Series
V
V
Physical
OUT
IN
8 and 10 Amp DC/DC Converters
5 sided
Input/Output Return
Corrosion-resistant steel with
non-conductive, epoxy-based, black
enamel finish and plastic baseplate
RoHS: Gold plate over copper alloy
Non-RoHS: Pure tin on copper alloy with
nickel underplate
7 Volts
15 Volts
15 Volts
None
None
Current limited. Devices can
withstand a sustained output
short circuit without damage.
–40 to +105°C
+300°C
(
1 –
V
V
OUT
IN
UNR18-33W.B01 Page 3 of 10
IN
)
to 1.8/2.5/3.3V
+1 508 339 3000
OUT