LSN2-T/22-D12NG-C Murata Power Solutions Inc, LSN2-T/22-D12NG-C Datasheet
LSN2-T/22-D12NG-C
Specifications of LSN2-T/22-D12NG-C
Related parts for LSN2-T/22-D12NG-C
LSN2-T/22-D12NG-C Summary of contents
Page 1
... LSN2 converters for local 1.8 and 3.3Vdc sup- plies. All system isolation resides in the central supply, leaving lower cost POL regulation at the load. The LSN2’s can deliver very high power (to 112 Watts tiny area without heat sinking or external components. They feature quick transient response (to 25μ ...
Page 2
... Regulation specifi cations describe the output-voltage deviation as the line voltage or load is varied from its nominal/midpoint value to either extreme. P Nominal line voltage, no-load/full-load conditions. Q LSN2-T/22-D12 effi ciencies are shown Max. output current is 20 Amps with V S This is an incomplete model number. Please refer to the Part Number Structure when ordering ...
Page 3
... L = 1μH. BUS BUS = +25°C, full output load, natural air convection. PCBOARD will cause the “ON” state for negative logic models. IN email: sales@murata-ps.com 25 Jun 2010 MDC_LSN2-T/22-D12_B03Δ = nominal OUT (12) max nominal, full load. “Nomi- OUT . A 68K: external pullup IN ...
Page 4
... I/O caps, and will operate within spec in most applications with no additional external components. In particular, the LSN2's input capacitors are specifi ed for low ESR and are fully rated to handle the units' input ripple currents. Similarly, the internal output capacitors are specifi ed for low ESR and full-range frequency response. ...
Page 5
... Input Fusing Most applications and or safety agencies require the installation of fuses at the inputs of power conversion components. The LSN2 Series are not inter- nally fused. Therefore, if input fusing is mandatory, either a normal-blow or a slow-blow fuse with a value no greater than twice the maximum input current calculated at low line with the converter's minimum effi ...
Page 6
... High-current-carrying components such as inductors, FET's and diodes are at the highest risk. LSN2 SIP Series DC/DC converters incorporate an output overcurrent detection and shutdown function that serves to protect both the power converter and its load. ...
Page 7
... The highest temperatures in LSN2 SIPs occur at their output inductor, whose 2 heat is generated primarily losses. The derating curves were developed using thermocouples to monitor the inductor temperature and varying the load to keep that temperature below +110°C under the assorted conditions of air fl ow and air temperature. Once the temperature exceeds +115°C (approx.), the thermal protection will disable the converter. Automatic restart occurs after the temperature has dropped below about +110° ...
Page 8
... Lastly, changing the timing may require reprogramming the logic sequencer or rewriting software. Sequence/Track Input A different power sequencing solution is employed on DATEL’s LSN2 DC/DC converter. After external input power is applied and the converter stabilizes high impedance Sequence/Track input pin accepts an external analog volt- ...
Page 9
... Sequencing controls on Point-of-Load (POL) converters. These circuits are only for reference and are not intended as fi nal designs ready for your application. Also, numerous connections are omitted for clarity. www.murata-ps.com LSN2-T/22-D12 Non-isolated, DOSA-SIP, (Fixed Cascaded Delays) email: sales@murata-ps.com 25 Jun 2010 MDC_LSN2-T/22-D12_B03Δ Page ...
Page 10
... POL’s to precisely track each other. www.murata-ps.com LSN2-T/22-D12 Non-isolated, DOSA-SIP, 22A Selectable-Output DC/DC Converters Figure 14. Proportional Phasing Figure 15. Sequence/Track Simplifi ed Equivalent Schematic powered all during the down ramp email: sales@murata-ps.com 25 Jun 2010 MDC_LSN2-T/22-D12_B03Δ Page ...
Page 11
... FET is at saturation, approximately +0.2V output. Keep this LOW (FALSE) pulldown current to less than 10mA. Please note that Power Good is briefl y false during Sequence ramp-up. Ignore Power Good while in transition. Figure 16. Equivalent Power Good Circuit www.murata-ps.com 25 Jun 2010 LSN2-T/22-D12 Non-isolated, DOSA-SIP, email: sales@murata-ps.com MDC_LSN2-T/22-D12_B03Δ Page ...
Page 12
... TYPICAL PERFORMANCE CURVES 22A Selectable-Output DC/DC Converters www.murata-ps.com 25 Jun 2010 LSN2-T/22-D12 Non-isolated, DOSA-SIP, email: sales@murata-ps.com MDC_LSN2-T/22-D12_B03Δ Page ...
Page 13
... Dimensions are in inches (mm) shown for ref. only. Third Angle Projection Tolerances (unless otherwise specified): .XX ± 0.02 (0.5) .XXX ± 0.010 (0.25) Angles ± 2˚ Components are shown for reference only. email: sales@murata-ps.com 25 Jun 2010 MDC_LSN2-T/22-D12_B03Δ © 2010 Murata Power Solutions, Inc. Page ...