MINI-PS-100-240AC/10-15DC/2 Phoenix Contact, MINI-PS-100-240AC/10-15DC/2 Datasheet - Page 8
![no-image](/images/manufacturer_photos/0/5/523/phoenix_contact_sml.jpg)
MINI-PS-100-240AC/10-15DC/2
Manufacturer Part Number
MINI-PS-100-240AC/10-15DC/2
Description
POWER SUPPLY PRIMARY SWITCH MODE
Manufacturer
Phoenix Contact
Datasheet
1.MINI-PS-100-240AC10-15DC2.pdf
(8 pages)
Specifications of MINI-PS-100-240AC/10-15DC/2
Power Supply Type
Switch Mode
Power Supply Output Type
Fixed
No. Of Output Channels
1
Output Voltage
12VDC
Output Current
2A
Input Voltage
85V To 265V
Supply Voltage Typ
110VAC / 230VAC
No. Of Outputs
1
Rohs Compliant
Yes
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Power Supply, Primary Switch Mode, Narrow Design – MINI-PS-100-240AC/10-15DC/2
7.2. Temperature Response
4 A up to an ambient temperature of 60°C (140°F).
With an ambient temperature of up to 40°C (104°F) the
device continuously supplies an output current of 5 A.
At temperatures up to 60°C (140°F), the POWER
BOOST provides a short-term output current of 6 A for
a few minutes.
Kelvin temperature increase for ambient temperatures
above +60°C (+140°F). At ambient temperatures
above +70°C (+158°F) or in the event of a thermal
overload, the device reduces the output power to
protect itself and returns to normal operation once it
has cooled down.
7.3. Parallel Operation
parallel to increase both redundancy and power. The
default setting does not have to be adjusted.
recommend that all cable connections from the power
supply to the DIN rail are the same length and have the
same cross section.
more than two power supplies a protective circuit
should be installed at each individual device output
(e.g., decoupling diode or DC fuse). This means that in
the event of a secondary device fault high return
currents are avoided.
7.4. Redundancy Operation
systems, which place particularly high requirements on
operational safety. If a fault occurs in the primary circuit
of device 1, device 2 automatically takes over the
complete power supply without interruption and vice
versa.
in parallel must be large enough that the total current
requirements of all loads can be fully met by one power
supply. External decoupling diodes are required for
100% redundancy.
7.5. Power Increase
n is the number of devices connected in parallel.
used to extend existing systems. A parallel connection
is recommended if the power supply does not cover the
current consumption of the most powerful load.
Otherwise, the loads should be divided over
independent individual devices.
parallel.
The device can supply a nominal output current of
The output power must be decreased by 5% per
Devices of the same type can be connected in
To ensure symmetrical current distribution we
Depending on the system, for parallel connection of
Redundant connections are designed for supplying
For this purpose, the power supplies to be connected
The output current can be increased to n x I
The parallel connection for power increase can be
A maximum of five devices can be connected in
PHOENIX CONTACT page 8 of 8
N
where
2.3
2.0
Σ =
MINI
10 - 15 V/
2 A
Σ =
MINI
10 - 15 V/
2 A
0
+
+
–
–
0
4 A
2 A
Ambient temperature [°C]
+ –
+ –
20
U
OUT
= 10 - 15 V
+
40
+
–
–
MINI
10 - 15 V/
2 A
MINI
10 - 15 V/
2 A
60
+ –
+ –
Figure 11
Figure 12
Figure 12