R21-62-20.0A-B101CV-V AIRPAX, R21-62-20.0A-B101CV-V Datasheet - Page 13
![CIRCUIT BREAKER, HYD-MAG, 2P, 125V, 20A](/photos/21/80/218002/4550260_sml.jpg)
R21-62-20.0A-B101CV-V
Manufacturer Part Number
R21-62-20.0A-B101CV-V
Description
CIRCUIT BREAKER, HYD-MAG, 2P, 125V, 20A
Manufacturer
AIRPAX
Series
Rr
Datasheet
1.PP11-2-10.0A-XX-V.pdf
(16 pages)
Specifications of R21-62-20.0A-B101CV-V
Input Voltage Vac
125V
No. Of Poles
2
Current Rating
20A
Interrupting Capacity
500A
Dielectric Strength
1.5kV
Trip Time
15s
Trip Time Max
15sec
Trip Time Min
1sec
Leaded Process Compatible
Yes
Rohs Compliant
Yes
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
http://airpax.sensata.com/
Note: Tolerance ± .010 [.25] unless noted. Dimensions in brackets [ ] are millimeters.
[17.27]
[15.88]
0.625
0.680
Knurled Nut
[13.56]
– 10 & –11
0.534
Hex Nut
– 31
Vertical Mount
OFF
ON
– A
Push-Pull & Push-to-Reset Hardware
Paddle Handle Hardware
[3.18]
0.125
[3.18]
0.125
3/8 - 32 Panel Nut
Bright Nickel
[1.98]
0.078
Horizontal Mount
O
F
F
[17.27]
[17.27]
0.680
0.680
Locking Ring (Toggle)
– B
– 20 & –21
Panel Dress Nut
– L
N
O
[3.96]
0.156
[0.79]
0.031
[4.57]
0.180
HARDwARE
Indicator Plates
SNAPAK
with indicator plates for either vertical or horizontal mounting.
The “ON-OFF/O-I” plate is standard.
Note 1:
To allow for installation clearances, the minimum
recommended distances between centers of panel openings
should be:
Note 2: Torque on mounting hardware is not to exceed 25
inch-pounds for 1 1/2 inch bushings or 15 inch-pounds for 3/8
inch bushings.
Mounting Nuts (Toggle)
A choice of knurled, dress and hex nuts are available. All three
are available in bright nickel. The knurled and dress nuts are
also available in a matte black finish. Every SNAPAK
with a hex nut, but you may order the front panel nuts which
will best enhance your design.
Miscellaneous Hardware
SNAPAK
equipped with optional locking rings to prevent rotation of the
unit after it is installed.
3/8 - 32 Hex Nut and Panel Nuts
The hardware will be supplied with each Push-Pull (PP)
and Push-to-Reset (PR).
3/8 - 32 Panel Nut
This nut when reversed will provide alignment in .437 (11.1)
and .468 (11.88) diameter round panel holes.
RECOMMENDED CENTER DISTANCES FOR PANEl OPENINGS
Breaker Type
PP11 & PR11
PP21 & PR21
T11
T21
R11
R21
®
®
circuit protectors with 1/2-32 thread may also be
toggle handle circuit protectors may be specified
SNAPAK® Series - Hardware
Distance, inches [mm]
0.750 [19.05]
1.375 [34.93]
0.750 [19.05]
1.375 [34.93]
0.805 [20.45]
1.429 [36.30]
®
comes
72