NC1V-1100F-0.5AM IDEC, NC1V-1100F-0.5AM Datasheet - Page 11
![CIRCUIT BREAKER, HYD-MAG, 1P, 250V 500mA](/photos/21/79/217996/4667630_sml.jpg)
NC1V-1100F-0.5AM
Manufacturer Part Number
NC1V-1100F-0.5AM
Description
CIRCUIT BREAKER, HYD-MAG, 1P, 250V 500mA
Manufacturer
IDEC
Datasheet
1.NC9Z-LK1.pdf
(12 pages)
Specifications of NC1V-1100F-0.5AM
Input Voltage Vac
250V
No. Of Poles
1
Current Rating
500mA
Interrupting Capacity
2.5kA
Dielectric Strength
2kV
Trip Time
600s
Voltage Rating Vdc
65V
Terminals
Screw
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
• 3-pole
• Installation Angle
Tripping method is hydraulic magnetic. Minimum operating
current varies with installation angle. Operating currents
are influenced by the weight of movable iron core. With
reference to the following figures, correct the rated current.
Minimum operating current is calculated from the following
formula:
(Minimum operating current) = (Rated current) ×
(Correction factor by installation angle) × (Reference
minimum tripping current rate)
• DIN Rails
[Installation on DIN Rail]
1. Fasten the DIN rail securely.
2. With the latch facing downward, install the NC1V circuit
[Removal from DIN Rail]
Using a flat screwdriver, pull the latch on the circuit
protector to remove from the DIN rail.
Instructions
protector on the DIN rail as shown below.
Installing
NC1V-3500
(Relay Trip)
Push
120%
100%
35mm-wide
DIN Rail
Flat
Srcrewdriver
52.5
47.0
ON
Removing
100%
M5 Terminal Screw (30A)
M3.5 Terminal Screw
2-ø4.5 Holes
(for screw mounting)
Latch
90%
35mm-wide
DIN Rail
6.6
Terminal Cover
Installation of Auxiliary/Alarm Terminal Cover
After wiring the terminals, install the terminal cover by
aligning with the circuit protector as shown below.
• Applicable Wire and Crimp Terminal
• For wiring the main circuit terminal, use the applicable crimp terminals and
• When using the NC1V circuit protector as CSA-certified product, use with CSA-
• When using the NC1V circuit protector as UL-listed product, use with UL-listed
Panel Mounting Screw (not supplied)
Product Markings (Example: NC1V-1111-30AA)
Terminal
Rated Voltage
Rated Current
tighten to the recommended torque.
certified crimp terminal.
crimp terminal.
Srew Type
Type No.
M4
66.0
Spring-up, fingersafe,
slotted Phillips screw
with square washer
(up to 20A)
Spring-up fingersafe
terminal
(25A and 30A)
Slotted Phillips screw
with square washer
48.3
Terminal Screw
33.0
5.0
DIN Rail (
NC1V Circuit Protectors
Tightening Torque
NC1V-1111
Ue 250VAC 50/60Hz · 65VDC
In 30A
Suppl. Prot.
0.8 to 1.0 N·m
BNDN1000
CIRCUIT PROTECTOR
220VAC
P
E
S
J E T
30A
CURVE A
125VAC 3A
AUX. SW
30 VDC 2A
)
A.T. 40°C
POLE 1
Connectable
JAPAN
0.25 to 1.65
1.04 to 2.63
2.63 to 6.64
0.25 to 1.65
1.04 to 2.63
2.63 to 6.64
0.25 to 1.65
1.04 to 2.63
I.C.2500A
Wire Size
(mm
PSE Certification
2
)
Terminal cover installed
No. of Poles
Time Delay Curve
Auxiliary/Alarm Contact Rating
Reference Operating
Temperature
Certification Marks
(M4 Mounting Screws)
Mounting Hole Layout
Spring Washer
Plain Washer
Applicable
R1.25-3.5
Crimping
Terminal
R1.25-4
R1.25-5
R5.5-4
R5.5-5
R2-3.5
All dimensions in mm.
R2-4
R2-5
47.0
Shape
Tightening
1.8 to 2.2
0.7 to 0.9
Torque
1 to 1.4
(N·m)
11