LMC200-2PS BLACK BOX, LMC200-2PS Datasheet - Page 3

• Manufacturer Part Number: LMC200-2PS
• Description: 14 SLOT POWER CHASSIS W/2 POWE
• Manufacturer: BLACK BOX

05/14/2010
#24868
724-746-5500
blackbox.com
850-nm multimode, 1300-nm multimode, and 1300-nm single-
mode models. The fiber length is limited to 1.2 miles (1.9 km)
per IEEE 802.3 timing.
support 50-ohm cable at distances of up to 607 feet (185 m). You
can connect up to 30 workstations to this segment per the 802.3
IEEE standard.
10BASE-T to 10BASE-FL
and fiber LANs into one network. They support half- and full-duplex
(10- and 20-Mbps) operation.
multimode, 1300-nm multimode, 1300-nm single-mode, or 1550-nm
single-mode.
RJ-45 connector and support Category 3, 4, and 5 wiring, connecting
at distances up to 328 feet (100 m).
reversals and eliminate crossed cables with a crossover switch.
100BASE-TX to 100BASE-FX
FX fiber to 100BASE-TX UTP LANs. They use auto-negotiation for
full- and half-duplex operation and can handle numerous fiber types.
supported by the device that is connected to the UTP port. When the
device supports full-duplex, the converter adapts to full-duplex mode
and creates a 200-Mbps bandwidth. When the connected device
supports only half-duplex, the converter adapts to this mode and
creates a 100-Mbps bandwidth. Full- and half-duplex operation
can also be controlled by a manual override switch.
nm and uses ST or SC connectors. Multimode models can support
distances of up to 1.2 miles (2 km), and the single-mode models
can operate at distances of 68.4 miles (110 km).
(100 m), has a modular 568 RJ-45 connector for Category 5 wiring.
A crossover switch eliminates the need for crossed cables.
Gigabit UTP to Fiber
Gigabit Ethernet 1000BASE-T unshielded twisted-
pair (UTP) cable to 1000BASE-SX single- or 1000BASE-LX multimode
fiber. The converters comply with the IEEE 802.ab standard.
services supported by the device connected to its UTP port. User-
selectable override options set the desired mode.
For fiber, these converters use ST connectors. They come in
On the coax side, the converters have BNC connectors and
A switch-selectable terminator is built in.
These media converters join unshielded twisted-pair (UTP)
For fiber, these converters use SC or ST
For UTP, these media converters use an EIA/TIA modular 568
10BASE-T to 10BASE-FL converters also correct wiring-polarity
This group of media converters connects Fast Ethernet 100BASE-
These converters auto-adapt to the highest performance level
The fiber side of these converters operates at 1300 nm or 1500
The UTP port, which supports distances of up to 328 feet
Use FlexPoint Gigabit UTP to Fiber Media Converters to convert
The converters auto-adapt to the full-/half-duplex and flow-control
®
connectors in 850-nm
2-Gbps data rate or in half-duplex mode to provide a 1-Gbps rate.
This maximizes the throughput when connecting to high-bandwidth
full-duplex services such as servers or switches.
selected “Pause” function that helps relieve network congestion
by providing “backpressure” to the sending device.
fiber and uses SC, MT-RJ, or LC connectors. The Multimode SX
supports distances of up to 722 feet (220 m); the single-mode models
support distances of up to 40.4 miles (65 km).
redundant network architectures as well as for connecting to SNMP
or other network-managed devices that monitor link availability.
A user-selectable override is provided to isolate the link detection
to a per-segment basis.
connector and supports Category 5 or higher wiring with distances
of up to 328 feet (100 m). Automatic polarity detection and correction
assists in network installation and maintenance.
Token Ring UTP/Fiber
models automatically sense and configure themselves to the network
ring speed. They also self-configure to attached devices through an
automatic sensing circuit.
ring-in/ring-out port, or lobe. This converter can also support server
or workstation fiber attachments and fiber ring extensions.
wiring can support distances of 492.1 feet (150 m). At 4 Mbps,
Category 5 wiring will support distances of 1604.4 feet (489 m). With
fiber, the converter supports 1.6 miles (2.6 km) using multimode fiber
and 12.4 miles (20 km) using single-mode fiber.
100-Mbps Fiber-to-Fiber Mode Converters
over multimode fiber. But between Media Converters, they connect
with single-mode fiber to give you distances up to 36.1 miles
(58.1 km).
3.1 miles (5 km).
Ethernet, and Fast Ethernet.
1000-Mbps Multimode-to-Single-Mode
to the network over multimode fiber and extend the network with
single-mode fiber. They support single-mode distances up to 31.1
The converters operate in full-duplex to provide an effective
Network flow control is supported via an auto-selected or user-
The converter supports 850-nm (SX), 1300-nm (LX), or 1550-nm
User-selectable Link Propagation is available for Spanning-Tree
The converter’s UTP port uses a modular EIA/TIA 568 RJ-45
For Token Ring LANs with fiber-to-copper conversions, these
The UTP port can attach to a workstation’s network interface card,
Category 3, 4, and 5 wiring can be used. At 16 Mbps, Category 5
These models also test cable integrity in the network.
Multimode-to-Single-Mode converters connect to the network
Multimode-to-Multimode versions extend your network up to
100-Mbps Fiber-to-Fiber Mode Converters support Token Ring,
1000-Mbps Multimode-to-Single-Mode converters connect
BLACK BOX
®
3 of 6