REM3RD ETERNA, REM3RD Datasheet - Page 2

• Manufacturer Part Number: REM3RD
• Description: EMERGENCY BULKHEAD, RECESSED, WHITE
• Manufacturer: ETERNA

Specifications of REM3RD

• Length: 410mm
• Width: 125mm
• Depth: 90mm
• Svhc: No SVHC (15-Dec-2010)
• Approval Bodies: BS EN 60598
• Base Type: T5 Fluorescent 8W
• Colour: White
• Supply Voltage: 240V
• Lamp Base Type: T5 Fluorescent 8W
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

General Information and Safety Instructions
Read this first
Check the pack and make sure you have all of the parts
listed on the front of this booklet. If not, contact the
outlet where you bought this product.
This product contains glass, care must be taken when
assembling, fitting or handling to prevent personal
injury or damage to the product.
This light fitting must be installed by a competent
person in accordance with the Building Regulations
making reference to the current edition of the IEE
Wiring Regulations (BS7671). The Building Regulations
may be obtained from HMSO or viewed and
downloaded from www.communities.gov.uk following
the link for Building Regulations.
As the buyer, installer and/or user of this product it is
your own responsibility to ensure that this fitting is fit
for the purpose for which you have intended it. Eterna
Lighting cannot accept any liability for loss, damage or
premature failure resulting from inappropriate use.
If in any doubt, consult a qualified electrician.
This product is designed and constructed according to
the principles of the appropriate British Standard and
is intended for normal service. Use of this fitting in any
other environment, for example in higher than normal
ambient temperatures, may result in a foreshortened
working life.
The lamp (tube) and batteries supplied with this fitting
are consumable parts and therefore may be outside of
any warranty offered.
Switch off the mains before commencing installation
and remove the appropriate circuit fuse.
When working at heights, please use a suitable
platform.
Suitable for indoor use only.
This product is suitable for installation on surfaces with
normal flammability (indicated by the “F” in a triangle)
e.g. wood, plasterboard, masonry. It is not suitable for
use on highly flammable surfaces (e.g. polystyrene,
textiles).
This product is suitable for mounting in plasterboard
ceilings, suspended ceilings* and similar board surfaces.
*check specification of ceiling for suitability.
Before making fixing hole(s), check that there are no
Eventually, you may want to replace this light fitting
When your light fitting comes to the end of its life or you choose to update or upgrade it by replacing
it, please do not dispose of it with your normal household waste, please recycle where facilities
exist. When you need to dispose of this fitting, check with your retailer or local authority for suitable
options. New regulations require the recycling of Waste from Electrical and Electronic Equipment
(European “WEEE Directive” effective August 2005—UK WEEE Regulations effective 2nd January 2007).
Environment Agency Registered Producer: WEE/GA0248QZ
obstructions hidden beneath the mounting surface
such as pipes or cables.
The chosen location of your new fitting should allow
for the product to be securely mounted and safely
connected to the mains supply (lighting circuit).
Do not attach to surfaces which are damp or freshly
painted.
If the location of your new fitting requires the provision
of a new electrical supply, the supply must conform
with the requirements of the Building Regulations
making reference to the current edition of the IEE
Wiring Regulations (BS7671).
This product is designed for permanent connection to
fixed wiring: this should be either a suitable lighting
circuit (protected with a 5 or 6 Amp MCB or fuse) or a
fused spur (with a 3 Amp fuse) via a fused connection
unit.
Make connections to the electrical supply in accordance
with the following code:
Live - Brown or Red
Neutral - Blue or Black
Earth - Green and Yellow
When making connections, ensure that the terminals
are tightened securely and that no strands of wire
protrude. Check that the terminals are tightened onto
the bared conductors and not onto any insulation. Wrap
loose terminal blocks well with insulating tape.
This product must be connected to Earth.
You are advised at every stage of your installation to
double-check any electrical connections you have
made. After you have completed your installation there
are electrical tests that should be carried out: these
tests are specified in the Wiring Regulations (BS7671)
referred to in the Building Regulations.
If in doubt, consult a qualified electrician.
Installation Instructions and Care
Installation
1.
2.
3.
4.
5.
6.
7.
8.
9.
10. Mark the current date on the battery pack.
11. Connect the battery pack to the circuit board.
12. Close the gear tray and secure using the screws
13. Check that the tube is correctly located in the
14. If you have chosen one of the drop-sign models,
15. Replace the diffuser or front plate and tighten
Undo the screws at each end of the diffuser
or front plate and lift off.
Decide which of the cable entries you need to use
and remove one of the knock-outs if necessary.
Cut the hole in your mounting surface using the
dimensions, see Fig 1.
Offer the fitting up through the hole in the ceiling
and allow to rest with the two large ears on the
top side of your ceiling, see Fig 2.
Undo the screws at each end of the gear tray and
allow to drop open.
Thread the mains supply cable in through the hole
in the back of the fitting.
Make the electrical connections according to the
colour code opposite. Take care not to leave any
strands protruding from the terminals and to
tighten all terminals securely. Ensure also that the
terminals clamp onto the bare wire and not onto
the insulation.
To operate the fitting in non-maintained mode,
remove the link from the terminals “S1” & “S2”.
If the lamp is to be switched, remove the link from
between the terminals marked “S1” & “S2” and
connect cables to and from your switch.
removed earlier, see Fig 3.
lampholders.
you need to fit the sign panel into the diffuser or
slotted front plate:
a) Offer the top of the sign panel into the slot
b) Fit the small split-pins into the holes at each
securely making sure that the fitting is properly
located around the hole in your ceiling, see Fig 5.
in the diffuser from beneath and press down
on the top of the diffuser until it rests on the
shoulders at the top of the panel.
end of the top edge of the sign panel and bend
the ends over to stop them from coming out
again, see Fig 4.
Fig. 1 Cut a hole in the ceiling
Fig. 2 Place
Fig. 3 Adjust
Fig. 4 Insert Pins
Fig. 5 Fix
Ceiling
Cover
Fitting
Screw
320mm
375mm
Insert pins in both sides and fold bac k
55mm