T513LS2W ETERNA, T513LS2W Datasheet - Page 2

• Manufacturer Part Number: T513LS2W
• Description: FLUORESCENT FITTING, T5 LINK, 570MM
• Manufacturer: ETERNA

Specifications of T513LS2W

• Supply Voltage: 230V
• Base Type: 525mm T5 Fluorescent 13W
• Power Rating: 13W
• Length: 570mm
• Svhc: No SVHC (15-Dec-2010)
• Colour: White
• External Length / Height: 570mm
• External Width: 21mm
• Height: 43mm
• Lamp Base Type: 525mm T5 Fluorescent 13W
• Depth: 55mm

Warning:
The leads supplied with your light fitting and the sockets incorporated in your fitting are designed to give protection
against any possible electrical hazard. The mains lead is terminated in a socket marked LS2S and this lead should be
used to supply mains to your fitting or chain of fittings. Under no circumstances should you attempt to adapt the link
lead to supply power to the opposite end of your fitting as this will leave live pins exposed at the mains input end of the
fitting. Altering or adapting any of the leads, other than shortening the mains supply lead, will invalidate your guarantee
and could present a severe electrical shock hazard.
Read this first:
>
>
>
>
>
>
>
>
>
>
>
Safety markings:
This light fitting must be installed in
accordance with the Building Regulations
making reference to the current edition of the IEE
Wiring Regulations (BS7671). The Building
Regulations may be obtained from HMSO or
viewed and downloaded from www.communities.
gov.uk following the link for Building Regulations.
If in any doubt, consult a qualified electrician.
Switch off the mains before commencing
installation and remove the appropriate circuit
fuse.
Disconnect the fitting from the electrical supply
before flash or high voltage testing.
Do not connect to a circuit which also has
inductive loads connected as spikes generated
switching inductive loads may damage electronic
components within your fitting.
Suitable for indoor use only.
This product is suitable for installation on surfaces
with normal flammability ( indicated by the "F" in a
triangle ) e.g. wood, plasterboard, masonry. It is
not suitable for use on highly flammable surfaces
( e.g. polystyrene, textiles ).
Before making fixing hole(s), check that there are
no obstructions hidden beneath the mounting
surface such as pipes or cables.
Do not attach to surfaces which are damp, freshly
painted or otherwise electrically conductive (e.g.
metallic surfaces).
If the location of your new fitting requires the
provision of a new electrical supply, the supply
must conform with the requirements of the Building
Regulations making reference to the current
edition of the IEE Wiring Regulations (BS7671).
This product is designed for permanent connection
to fixed wiring: this should be either a suitable
lighting circuit ( protected with a 5 or 6 Amp MCB
or fuse ) or a fused spur ( with a 3 Amp fuse ) via a
>
>
>
Installation:
1)
2)
3)
4)
5)
6)
7)
fused connection unit. We recommend that the
supply incorporates a switch for ease of operation.
Make connections to the electrical supply in
accordance with the following code:
This fitting is double insulated, do not connect any
part to earth.
You are advised at every stage of your installation
to double-check any electrical connections you
have made. After you have completed your
installation there are electrical tests that should be
carried out: these tests are specified in the Wiring
Regulations ( BS7671 ) referred to in the Building
Regulations. If in doubt, consult a qualified
electrician.
When positioning the fitting, make sure there is a
gap of at least 10mm between the lamp and any
adjacent surface. See figure 1, opposite.
Select the type of brackets you need to use and
mark off the fixing points—see diagram N°3
opposite for best spacing. If fixing to a shelf or
under a cupboard, check the screw size required
and screw into place. See figures 2 and 3,
opposite.
If fixing directly to the wall, drill holes using a N°8,
5mm drill bit to a depth of 30mm and insert wall
plugs.
Secure the selected brackets in place using the
screws supplied.
Attach the fitting to the clips.
Connect the mains lead or link lead to the socket
on your fitting.
Restore the power supply and switch on.
Live - Brown or Red
Neutral - Blue or Black
How to link multiple fittings together.
Option 1. The light fittings can be butted together to form a line of up to a maximum of 6 fittings. Simply
remove the connector caps and push the fittings together using the short butt connector supplied.
Use the mains lead cable to connect the first fitting and the mains via a
spur or junction box.
Option 2. Connect link leads between each fitting and once all lights have
been connected, connect the mains lead to the mains via a spur or junction
box.
mains lead
2
1
End view
10mm gap
1/4
Fixing clips
2/4
butt connector
1/4
10mm gap
End view
End view
Link lead
Fixing clip
“F” mounting clip
“C” mounting clip
3
Link lead
Fixing clip
End view