HFBR-57E5APZ Avago Technologies US Inc., HFBR-57E5APZ Datasheet - Page 5

• Manufacturer Part Number: HFBR-57E5APZ
• Description: MM LC SFP FE DMI ROHS
• Manufacturer: Avago Technologies US Inc.

Specifications of HFBR-57E5APZ

• Data Rate: 125MBd
• Wavelength: 1310nm
• Applications: Ethernet
• Voltage - Supply: 3 V ~ 3.6 V
• Connector Type: LC Duplex
• Mounting Type: SFP
• Optical Fiber Type: TX/RX
• Optical Rise Time: 3/2.2ns
• Optical Fall Time: 3/2.2ns
• Operating Temperature Classification: Industrial
• Peak Wavelength: 1308/1380nm
• Package Type: SFP
• Operating Supply Voltage (min): 3V
• Operating Supply Voltage (typ): 3.3V
• Operating Supply Voltage (max): 3.6V
• Operating Temp Range: -40C to 85C
• Mounting: Snap Fit To Panel
• Pin Count: 20
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

Table 2. Pin Description
Notes:
1. Pin 2 is connected to internal ground.
2. Mod-Def 0, 1, 2 are the module definition pins. They should be pulled up with a 4.7 k: to 10 k: resistor on the host board to a supply less than
3. LOS (Loss Of Signal) is an open collector/drain output which should be pulled up with an externally with a 4.7 k: to 10 k: resistor on the host
4. RD-/+: These are the differential receiver outputs. They are AC-coupled to 100 Ω differential lines which should be terminated with 100 : differential
5. V
6. TD-/+: These are the differential transmitter inputs. They are AC-coupled differential lines with 100 : differential termination inside the module.
5
Pin
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
V
Mod-Def 0 is grounded by the module to indicate that the module is present.
Mod-Def 1 is the clock line of the two-wire serial interface.
Mod-Def 2 is the data line of the two-wire serial interface.
board to a supply less than V
sensitivity (as defined by the standard in use). In the low state, the output will be pulled to a voltage less than 0.8 V.
at the SERDES. AC-coupling is present inside the module and is thus not required on the host board.
AC-coupling is present inside the module and is thus not required on the host board.
CC
CC
T + 0.3 V or V
R and V
CC
Name
V
NC
Tx Disable
MOD-DEF2
MOD-DEF1
MOD-DEF0
NC
LOS
V
V
V
RD-
RD+
V
V
V
V
TD+
TD-
V
EE
EE
EE
EE
EE
CC
CC
EE
EE
T are the receiver and transmitter power supplies. They are defined as 2.97 V to 3.63 V at the SFP connector pin.
T
R
R
R
R
T
T
R
T
CC
R + 0.3 V. In order to use this interface, supply 3.3 V to V
CC
T, R + 0.3 V. When high, this output indicates that the received optical power is below the worst case receiver
Function/Description
Transmitter Ground
NC
Transmitter Disable – Module disables on high or open
Module Definition 2 – Two wire serial ID interface
Module Definition 1 – Two wire serial ID interface
Module Definition 0 – grounded in module
NC
Loss of Signal – high indicates loss of signal
Receiver Ground
Receiver Ground
Receiver Ground
Inverse Received Data Out
Received Data Out
Receiver Ground
Receiver Power 3.3 V ± 10%
Transmitter Power 3.3 V ± 10%
Transmitter Ground
Transmitter Data In
Inverse Transmitter Data In
Transmitter Ground
CC
T.
MSA Notes
1
2
2
2
3
4
4
5
5
6
6