AH-5A BOGEN COMMUNICATIONS, AH-5A Datasheet - Page 33

• Manufacturer Part Number: AH-5A
• Description: Amplified Speaker/horn
• Manufacturer: BOGEN COMMUNICATIONS

Specifications of AH-5A

• Peak Reflow Compatible (260 C): No
• Leaded Process Compatible: No
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant

P r o d u c t F e a t u r e s :
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
SINGLE-ZONE TELEPHONE INTERFACE
Single-Zone Universal Telephone
Interface
UTI1
UTI1 Control Panel
Bogen’s UTI1 is a single-zone telephone interface that is compatible with all standard analog
port types. A background music (BGM) input with variable muting coordinates music
and page announcements. An additional audio output provides a “page only” function
(no BGM) for application flexibility. A built-in 24V DC, 1A power supply is provided for
powering amplified speakers. Paging volume controls are provided for each of the outputs.
An output limiter function, with limiter active indicator, provides consistent page volume
regardless of loud or soft paging announcements. Contact-triggered tones and night ring
signals, as well as programmable AUX relay contacts, are all programmed using DTMF
tones through the dual purpose override input. Plug-in terminal strips provide for easy
installation. An optional security cover/rack mount kit (RPKUTI1) is available.
or without contact closure activation)
(no BGM) outputs
control and variable muting
and slow whoop tone selections
Emergency override & general paging
One-way paging only
Interfaces to Loop Start, Ground Start,
Analog Station, and Page Ports (with
Simple 2-switch interface setup
Background music (BGM) input with level
Separate Page & BGM and Page Only
Level control for each output
24V DC, 1A power supply
150 Speaker T/R drive capacity per output
Override input (loop start or page port)
Contact-triggered Night Ring input
Programmable AUX Relay
Pre-announce/confirmation tone
Tone burst (2 to 7 sec), chime,
Page level limiter with active indicator
Adjustable automatic level control
Requirements
120V AC,
Power
0.5A
•
•
•
•
•
•
•
•
•
•
•
•
programmable
Microcontroller operated, DTMF
Night ring tone or chime selection
Setup test tone
Pluggable terminal strip connectors
Programming through override jack
Programmable timeout for station mode
Programmable trunk port timeout
Responds to CPC disconnect signal
Wall-mount design
Rack-mountable with RPKUTI1 kit (optional)
FCC registered
UL and C-UL listed
12-1/4
(without rack mount kit)
"
W X 5-1/4" H X 2-1/2" D
rack mount / security cover kit
Dimensions
UTI1
shown with optional
Product
Weight
5 lb.
Programmable AUX Relay
The UTI1 provides a way for in-
stallers to decide how the AUX
relay contacts will trip based on
which inputs on the UTI1 are ac-
tive. The UTI1 has 4 inputs:
override, tone trigger, paging,
and night ring. The installer can
program the AUX relay to re-
spond to one or any combination
of these inputs. The UTI1 priori-
tizes these inputs (in the order
shown above) so that higher pri-
ority inputs preempt lower ones,
but the AUX relay contacts can be
programmed to work independ-
ently of this hierarchy.
For example, the AUX relay could
be programmed to respond only
to a night ring trigger independent
of anything else the UTI1 was
doing. The UTI1 would suppress
the night ring tone if a general
page were made; however with
the AUX relay programmed this
way, the AUX relay contacts
would remain active until the
night ring input stopped regard-
less of the other UTI1 inputs.
The AUX relay contacts can also
be programmed to operate after
the triggering event has finished.
In this case, the AUX relay contact
activates for 1 second and then
stops. This type of operation allows
external equipment to be triggered
after an event has occurred.
All this selectable functionality
allows the installer improved
ways to control external equip-
ment in conjunction with the
UTI1 operation. Programming is
accomplished through simple
DTMF programming codes.
Accessories
RPKUTI1
Security Cover & Rack Mount Kit
(sold as a set)
31