V60 BOGEN COMMUNICATIONS, V60 Datasheet - Page 3

• Manufacturer Part Number: V60
• Description: Power Vector Modular Input Amplifiers
• Manufacturer: BOGEN COMMUNICATIONS

Specifications of V60

• Peak Reflow Compatible (260 C): No
• Leaded Process Compatible: No
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant

Signal-Processing Output Modules
Modular
Flexibility
Wide Selection of Advanced Plug-In Modules
Bogen's new advanced input modules provide a wide range of input types allowing for custom configuration of
inputs - in both type and number - for a particular application. Modules are fully-featured for their application, many
with Bass/Treble, Gain, Music Ducking, Mute Send, and Mute Receive. Mix and match a variety of modules to meet
your specific installation needs. Each of Bogen's modules support different signal-source/processing requirements.
Included interface features are: balanced and unbalanced inputs; stereo or mono; telephone systems/PBXs; trans-
former-isolated; microphones; tone generator; and bridging.
Signal-Processing Output Modules
Bogen's new output modules offer a cost effective and convenient way to add specific signal processing capability
into a system. These modules automatically insert themselves into the audio signal path and eliminate the need for
external wiring as well as accessory outboard equipment. The selection includes an ambient noise sensor, compres-
sor/limiter, and parametric equalizer. Each Power Vector amplifier accepts up to two signal-processing output modules.
The amplifier automatically detects the presence of an installed signal-processing output module, and automatically
inserts it into the audio signal path of the amplifier. All connections are done internally, so there is no need for patch cords
to connect to the inserts. When two output modules are installed, the signal processing effects are cascaded. In addition,
each output module includes an unbalanced input that is controlled by the amplifier's input control so an input is not forfeit-
ed when an output module is used.
(1) the effects insert jacks are still available for use by external processing equipment.
(2) the signal processing output modules act on the signal on the raw mix bus signal before any other user controls
RELAY INPUT/OUTPUT - RIO1S
COMPRESSOR LIMITER - CMP1R
(such as volume, bass, and treble) can affect it. This then ensures that signal level dependent processors, such as
the Compressor/Limiter and the Ambient Noise Sensor modules, perform as intended regardless of front panel
control changes (excluding input volume controls).
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Transformer-isolated, balanced line-level input
600-ohm or 10k jumper selectable input impedance
8-ohm, 750mW output
Input and output level controls
Relay responds to selectable priority level
External control of priority muting
N.O. or N.C. relay contacts
Input can be muted from higher priority modules,
Output can gate with relay priority level
Screw terminal strips
RJ11 connection with line output and dedicated
N.O. relay contact
Compressor Ratio control
Make-up Gain control
Bypass switch
Unbalanced input
Gradual fade back from mute
Mutable input
RCA connector
with signal fade back
Threshold control
PARAMETRIC EQUALIZER - PEQ1R
AMBIENT NOISE SENSOR - ANS1R
with Sensor
Microphone
ANS1R
Automatically insert themselves into the mix bus signal
path leading to the power amp stage when installed.
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Unbalanced input
Gradual fade back from mute
2 full parametric bands
Frequency control
‘Q’ bandwidth control
Gain control
Bass and Treble control
Bypass switch
Mutable input
Gradual fade back from mute
RCA connector
Maximum Gain control
Ramp Speed control
Stereo AUX input
Connect up to 4 sensor mics
Mutable input
RCA connectors
Accessories
Activity Threshold control
Ambient MIC input threshold control
AUX level input control
ANS500M
(One included; additional available)
Sensor Microphone
All Modules Sold Separately
3