BIM2H-433-64 RADIOMETRIX, BIM2H-433-64 Datasheet

TRANSCEIVER, 433.92MHZ

BIM2H-433-64

Manufacturer Part Number
BIM2H-433-64
Description
TRANSCEIVER, 433.92MHZ
Manufacturer
RADIOMETRIX
Datasheet

Specifications of BIM2H-433-64

Rohs Compliant
YES
BiM2A is a half-duplex crystals controlled PLL
wideband FM transceiver operating on 433.05-
434.79MHz European SRD band.
It is an enhanced replacement for the SAW
based BiM2 and has better frequency accuracy
and temperature stability.
BiM2H is a high power version with 25mW RF
power and specifically made available for
Australian/New Zealand users.
Features
Instead of the SAW-based technology of the BiM2, the BiM2A and BiM2H use a PLL circuit locked to a
crystal for better frequency stability over a wider temperature range (-20C to +70C) and supply range
(2.9 – 16V), at the expense of slightly slower power-up. The BiM2A is available as standard on
frequencies of 433.92MHz and 434.42MHz.
The BiM2H can be made available if required in an extra-high-power version (BiM2EH), in the same
footprint and pinout but giving 100mW nominal output power at 3.7 - 16V supply with a current
consumption of less than 45mA.
Applications
Radiometrix Ltd, BiM2A Data Sheet
23 April 2007
Data rates up to 64kbps
Crystal controlled PLL FM circuitry for both Tx and Rx
Receiver Sensitivity:
Supply: 2.9V - 16V @ 14mA TX (10mW), 25mA TX (25mW), 11mA Rx
Usable range up to 300 metres external, 75 metres in building
SAW front end filter and full screening
RSSI (standard) or carrier detect option
Analogue and digital baseband
Low profile with small footprint
33 x 23 x 5mm
Conforms to European EN 301 489-3 and ETSI EN 300 220-3 (ERP @ 10mW)
Conforms to Australian/New Zealand AS/NZS 4268:2003 (ERP @ 25mW)
PDAs, organisers and laptops
Handheld terminals
EPOS equipment, barcode scanners, belt clip printers
Data loggers
Audience response systems
In-building environmental monitoring and control
Security and fire alarms
Restaurant ordering systems
Vehicle data up/download
433MHz Wide Band FM radio transceiver
Hartcran House, 231 Kenton Lane, Harrow, HA3 8RP, England
Radiometrix
Tel: +44 (0) 20 8909 9595, Fax: +44 (0) 20 8909 2233
-101dBm for 1ppm BER (64kbps)
-104dBm for 1ppm BER (10kbps)
BiM2A/BiM2H
Fig. 1: BiM2H-433-64
page 1

Related parts for BIM2H-433-64

BIM2H-433-64 Summary of contents

Page 1

... PDAs, organisers and laptops Handheld terminals EPOS equipment, barcode scanners, belt clip printers Data loggers Audience response systems In-building environmental monitoring and control Security and fire alarms Restaurant ordering systems Vehicle data up/download Radiometrix Ltd, BiM2A Data Sheet BiM2A/BiM2H Fig. 1: BiM2H-433-64 page 1 ...

Page 2

... See page.6 for typical characteristics. CD pin 11 Carrier Detect - When the receiver is enabled, a low indicates a signal above the detection threshold is being received. The output is high impedance (50k ) and should only be used to drive a CMOS logic input. Radiometrix Ltd, BiM2A Data Sheet Loop Filter 32 ...

Page 3

... DC +ve supply pin. +2.9 to +16 volts @ <14mA (@10mW). The supply should be clean, <20mV side view (through can) RF GND 1 Antenna 2 RF GND pin Radiometrix Ltd, BiM2A Data Sheet Function Power down (<10 A) Receiver enabled Transmitter enabled Self test loop-back* top view (without can ...

Page 4

... TX & RX select: high (deselect) low (select) Internal select pull-ups Balanced code bit rate Balanced code bit rate Transmitter section RF power output (BiM2A) RF power output (BiM2H) RF power output (BiM2EH) TX harmonics/spurious emission Initial centre frequency accuracy FM deviation Modulation bandwidth Modulation distortion TX spectral bandwidth @-40dBc ...

Page 5

... Although the module baseband response extends down to DC, data formats containing a DC component are unsuitable and should not be used. This is because frequency errors and drifts between the transmitter and receiver occur in normal operation resulting in DC offset errors on the AF output. Radiometrix Ltd, BiM2A Data Sheet pin min. ...

Page 6

... This antenna is simple, cheap, easy to set up and performs well especially effective when used with a ground plane, which in practice is often provided by the main PCB metal case. Radiometrix Ltd, BiM2A Data Sheet : 50-75m : 200-300m ...

Page 7

... R&TTE directive. 4) The BiM2A has not been tested with antennas having gains greater than that of a quarter-wave whip. The use of such antennas may require further R&TTE approval. Radiometrix Ltd, BiM2A Data Sheet 0.5 mm enameled copper wire close wound on 3.2 mm diameter former ...

Page 8

... BiM2A-433-64-CD-5V +10dBm BiM2A-433-10-CD-5V +10dBm RSSI versions BiM2A-433-64 +10dBm BiM2A-433-10 +10dBm BiM2H-433-64 +14dBm BiM2H-433-10 +14dBm BiM2EH-433-64 +20dBm BiM2EH-433-10 +20dBm For 434. Note: Non-standard frequency variants can be supplied to individual customer requirements. Minimum order quantities apply. Please consult the Sales department for further information. ...

Page 9

... Copyright notice This product data sheet is the original work and copyrighted property of Radiometrix Ltd. Reproduction in whole or in part must give clear acknowledgement to the copyright owner. Limitation of liability The information furnished by Radiometrix Ltd is believed to be accurate and reliable. Radiometrix Ltd reserves the right to make changes or improvements in the design, specification or manufacture of its subassembly products without notice ...

Related keywords