TG310 AIM-TTI INSTRUMENTS, TG310 Datasheet - Page 2

• Manufacturer Part Number: TG310
• Description: FUNCTION GEN, 3MHZ VERNIER
• Manufacturer: AIM-TTI INSTRUMENTS

Specifications of TG310

• Signal Generator Type: Function
• Bandwidth: 3MHz
• Supply Voltage Range: 110V To 240V
• External Height: 88mm
• External Width: 260mm
• External Depth: 235mm
• Svhc: No SVHC (15-Dec-2010)
• Output: RoHS Compliant

A basic generator of high performance
The TG310 is a basic 3MHz function generator which offers very high
waveform quality at all frequencies and levels. Frequency is set us-
ing a calibrated vernier knob.
The feature set includes variable symmetry and variable dc offset
with centre detent.
Output impedances of 50W and 600W are supported via separate out-
put sockets.
Main Features
u
u
u
u
u
u
u
Part of an extensive range
TTi offers a wide choice of function generators both analogue and
digital, from this basic 3MHz model up to a highly sophisticated
50MHz unit.
Users requiring an analogue function generator with digital readout
and a wider feature set should request information on the TG300 se-
ries of 3MHz generators.
Technical Specifications
Frequency Range:
Vernier Range:
Vernier Accuracy:
Specifications apply for the top decade of each frequency range and maximum out-
put into 50 W termination.
SINE
Distortion:
Amplitude Flatness:
TRIANGLE
Linearity:
SQUARE WAVE
Rise/Fall Times:
Mark - Space Ratio:
DC
Range:
SYMMETRY
Symmetry Range:
TG310 - 3MHz function generator
FREQUENCY
OPERATING MODES
Glebe Road, Huntingdon. Cambs. PE29 7DR United Kingdom (UK)
Designed and built in Europe by:
0.003Hz to 3MHz frequency range
High waveform quality at all frequencies & levels
20mV to 20V pk-pk from 50 W or 600 W
Auxiliary TTL/CMOS output
Variable symmetry with constant frequency
Variable DC offset with zero detent
1000:1 frequency change by vernier or sweep voltage
Email: [e-mail]
Tel: [phone] Fax: [phone]
Thurlby Thandar Instruments Ltd.
0.003Hz to 3MHz in 7 overlapping decade ranges
with fine adjustment by a vernier.
1000:1 on each range.
Typically ±5% of full scale.
<0.5% on 3, 30 and 300Hz ranges; <1% on 3k,
30k and 300k ranges; all harmonics >25dB below
fundamental on 3M range.
±0.2dB to 200kHz; ±2dB to 3MHz.
Better than 99% to 200kHz
<100ns
1:1 ± 1% to 100kHz
±10V unterminated
Variable typically 1:9 to 9:1 (on top decade of each
range), frequency divided by 10.
Web: www.tti-test.com
MAIN - 50 Ohm
Amplitide
Attenuator Ranges:
DC Offset Range:
MAIN - 600 Ohm
AUX OUT
Input Impedance:
Input Sensitivity:
Max. Input Voltage:
Sweep Linearity:
Max. Slew Rate:
CASING
Moulded ABS case with tilt stand.
POWER REQUIREMENTS
Input Voltage:
Power Consumption:
TEMPERATURE & ENVIRONMENTAL
Operating Temp
Range:
Storage Temp.
Range:
Environmental:
SIZE
WEIGHT
SAFETY
EMC
Thurlby Thandar Instruments Ltd. operates a policy of continuous development and
reserves the right to alter specifications without prior notice.
OUTPUTS
SWEEP (EXTERNAL)
GENERAL
2mV to 20V peak-peak open circuit (1mV to 10V
peak-peak into 50W) in four switch selectable
ranges with 20dB vernier control within each range.
0dB, -20dB, -40dB, -60dB
±10V from 50W. DC offset plus signal peak limited
to ±10V (±5V into 50W). DC offset plus wave-
form attenuated proportionally by the attenuator.
Alternative output socket offering the same facilities
as the 50W socket.
0 to 5V TTL/CMOS logic levels capable of driving 2
standard TTL loads. Frequency, symmetry and
phase as main outputs
10kW
0 to 3V for 1000:1 sweep
±10V
Better than 1%
0.1V/us
220 to 240 volts AC nominal 50/60Hz or
110 to 120 volts AC nominal 50/60Hz by rear panel
adjustment. Installation category II.
25VA max.
+5
-10
Indoor use at altitudes up to 2000m.
Pollution degree 2.
260(W) x 88(H) x 235(D)mm (10.2 x 3.4 x 9.2"), ex-
cluding tilt stand and feet.
1.9kg (4.2lb)
Complies with EN61010-1.
Complies with EN61326.
o
C to +40
o
C to +65
o
C, 20% to 80% RH.
o
C
82100-00XX