376A-1 ELKAY, 376A-1 Datasheet

TIMER, PIR SENSOR, WALL, VARIABLE

376A-1

Manufacturer Part Number
376A-1
Description
TIMER, PIR SENSOR, WALL, VARIABLE
Manufacturer
ELKAY
Datasheet
1.376A-1.pdf (2 pages)

Specifications of 376A-1

Time Range
2min To 2h
Colour
White
Contact Current Max
16A
Current Rating
16A
Mounting Type
Surface Mount
No. Of Inputs
2
Supply Voltage
240V
For Use With
Lighting, Heating, Ventilation
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
pirtimer
pirtimer fitting & operating instructions
Product: 376A-1, 376A-2, 770A-1, 570A-3, 570A-4 Two wire.
The pirtimer is part of the Elkay family of switches, timers and detectors which save energy
and increase convenience in and around your home, garden or premises.
WHEN USED WITH SOME LOW WATTAGE LIGHTING, PLEASE ENSURE
A POWER FACTOR CORRECTION CAPICATOR OF 2 MICROFARADS
(MINIMUM) IS FITTED.
USAGE
The PIR timer has been designed to replace a single gang light switch, to control
lighting, heating and ventilation. The unit is switched on by the detection of moving
body heat within a specified range. When body heat is no longer detected, the unit
will switch off after the adjustable time period has elapsed. If moving body heat is
detected again during the timing period, the timing sequence will restart. The unit has a
lux level adjustment, which measures the ambient light levels and prevents lighting
being switched on when there is sufficient light in the room.
Your Elkay PIR timer has the added benefit of a manual override facility. This allows the
lights to be turned on for the set period of time when the ambient light level is such
that the lights would not usually come on. In dark conditions the manual override
disables the PIR allowing the lights to be turned off indefinitely or when the override
switch is re-pressed.
POSITIONING
Use the detection range to determine a suitable location for the
sensor. When locating the position of the unit avoid subjecting the
sensor to direct sunlight. Ensure that the sensor is not adjacent to the
load. Do not site the unit on a vibrating surface, or near a forced air
heating or ventilation. (see diagram 2)
MOUNTING AND INSTALLATION
Important Please note that it is essential that the Live In wire and
switch Live Out is identified prior to commencing installation. Turn
off mains supply for installation. Your Elkay unit is compatible with a
single gang, 25mm deep, British Standard accessory plate. Please ensure that the top and bottom lugs are removed, if fitted,
from metal wall boxes prior to fitting. Ensure that there is adequate space for wiring.
Step 1 Place the Live In wire, as per diagram, into the left hand position of the connector, the switched Live Out wire into
the second from left position of the connector. (see diagram 1)
Step 2 To set time, as per timing table, use switches one through three. Depending on required time available from 2
minutes to 2 hours. E.g 10 minutes = switch one – off, switch two – on, switch three – off. (see diagram 3)
2 mins
4.
3.
2.
1.
5 mins
4.
3.
2.
1.
Elkay Electrical, Coleshill, Birmingham, England.
Tel: +44 (0) 1675 468222 www.elkay.co.uk
10 mins
4.
3.
2.
1.
20 mins
Diagram 3
4.
3.
2.
1.
40 mins
Patent Pending Inst. Ref. No PIR201 Rev. No.: 04/07
4.
3.
2.
1.
5 - 7m
60 mins
4.
3.
2.
1.
Diagram 2
90 mins
RATING AT 240V AC
Incandescent 16A
Fluorescent
Compact
Fluorescent
Time Delay
Diagram 1
4.
3.
2.
1.
5 - 7m
adjustment
Lux level
16A
16A
2mins - 2hours.
120 mins
switches
Battery
4.
3.
2.
1.
DIL
LIVE OUT
LIVE IN
4.
3.
2.
1.

376A-1 Summary of contents

Page 1

... Product: 376A-1, 376A-2, 770A-1, 570A-3, 570A-4 Two wire. The pirtimer is part of the Elkay family of switches, timers and detectors which save energy and increase convenience in and around your home, garden or premises. WHEN USED WITH SOME LOW WATTAGE LIGHTING, PLEASE ENSURE A POWER FACTOR CORRECTION CAPICATOR OF 2 MICROFARADS (MINIMUM) IS FITTED ...

Page 2

... N.B The PIR lens will require approximately 1 minute to initialise. OPERATION NOTES If the Elkay PIR timer does not receive power for a period of over seven days, please turn battery off, using switch 4. In the case of power failure, your Elkay PIR timer will attempt to automatically re-start, which will cause the blue locator ring to flash ...