MC36344 MULTICOMP, MC36344 Datasheet

ESD BENCH MAT

MC36344

Manufacturer Part Number
MC36344
Description
ESD BENCH MAT
Manufacturer
MULTICOMP
Datasheet
1.MC36344.pdf (2 pages)

Specifications of MC36344

Mat Type
Bench
Mat Color
Green
Mat Material
Rubber
Ground Terminals
Snap
Length
50ft
External Width
2.5ft
Thickness
2mm
Surface Resistivity Mm
1Mohm/sq
Mat Features
Static Dissipative
ESD Bench Matting - Smooth Finish - Green
GROUNDING:
Sufficient ground cords should be used to reliably meet EN 61340-5-1 Table 3 less than 1 x 10
Industry recommendation is that continuous runs of ESD matting should be grounded at 10ft intervals to allow proper charge
decay rates. Each individual ESD mat should be grounded with ground snaps located no further than five feet from either end.
CLEANING:
Please note that contact between the matting surface and any acid or alkali solvent is strictly prohibited (such as Benzene,
Alcohol etc), this will result in the antistatic performance wearing away. If cleaning is required, the matting may be wiped with
a cloth coated in a neutral solution (such as water).
CUTTING TOLERANCES: Width + 6mm, Length + 6mm every linear foot of running material.
Construction:
Disclaimer: This data sheet and its contents (the “Information”) belong to the Premier Farnell Group (the “Group”) or are licensed to it. No license is granted for the use of it other then for information purposes
in connection with the products to which it relates. No license of any intellectual property rights is granted. The Information is subject to change without notice and replaces all data sheets previously supplied.
The Information supplied is believed to be accurate but the Group assumes no responsibility for its accuracy or completeness, any error in or omission from it or for any use made of it. Users of this data sheet
should check for themselves the Information and the suitability of the products for their purpose and not make any assumptions based on information included or omitted. Liability for loss or damage resulting
from any reliance on the Information or use of it (including liability resulting from negligence or where the Group was aware of the possibility of such loss or damage arising) is excluded. This will not operate to
limit or restrict the Group’s liability for death or personal injury resulting from its negligence. SPC Multicomp is the registered trademark of the Group. © Premier Farnell plc 2008.
Features:
Anti-static matting should be laid out in the workshops
or advanced laboratories for microelectronic industries
such as electronic semi-conduct devices, electronic
computers, electronic communication equipment and
integrated circuits etc.
•
•
•
•
•
•
•
http://www.farnell.com
http://www.newark.com
http://www.cpc.co.uk
materials with synthetic rubber
Great value ESD Bench Matting
Made from anti-static (conductive) and static-dissipative
2mm thick double-layer structure
Surface layer is a 0.5mm thick static-dissipative layer
Bottom layer is a 1.5mm conductive layer
Asian origin
Blue and Gray colours also available upon request
Static Dissipative Layer
Conductive Layer
SPC
SPC
Colours / Finish:
082-0203 ESD Bench Matting - Smooth Finish MC36344 MC | November 10, 2010 9:51 AM
Green
SPC
SPC
9
ohms for working surfaces.

MC36344 Summary of contents

Page 1

... Group’s liability for death or personal injury resulting from its negligence. SPC Multicomp is the registered trademark of the Group. © Premier Farnell plc 2008. http://www.farnell.com http://www.newark.com http://www.cpc.co.uk SPC Colours / Finish: Static Dissipative Layer Conductive Layer SPC 082-0203 ESD Bench Matting - Smooth Finish MC36344 MC | November 10, 2010 9:51 AM SPC Green ohms for working surfaces. 9 SPC ...

Page 2

... YY-1001 YY-1001 N/A N/A ohms. ANSI/ESD S-20.20 has an upper limit of <1 x10 is >1x10 ohms Size: 2.5 x 50’ SPC 082-0203 ESD Bench Matting - Smooth Finish MC36344 MC | November 10, 2010 9:51 AM SPC Unit: Value: Ω 1x10 < R < 1x10 6 Ω 1x10 < R < 1x10 3 Ω ...