DATAMAN-448PRO2 DATAMAN, DATAMAN-448PRO2 Datasheet - Page 2

• Manufacturer Part Number: DATAMAN-448PRO2
• Description: 448PRO2 MULTI SOCKET 48-PIN PROGRAMMER W/ ISP
• Manufacturer: DATAMAN

Specifications of DATAMAN-448PRO2

• Ic Product Type: Programmer, Universal
• No. Of Devices Supported: 51000
• Features: Up To 70% Faster Programming Of High Capacity Memory Devices, Windows7 Compatible
• Kit Contents: Gang Programmer, USB Cable, ISP Cable, User Manual, Software, Transport Case

Programmer Specification
• 4 x universal programming modules (4 x 48-pin DIL ZIF sockets and 4 x ISP
• Power and operation status LEDs
• USB 2.0 high-speed compatible port
• Protection against surge and ESD on power supply input
• Banana jack for ESD wrist strap connection
• Banana jack for connection to ground
Module Specification
Base Unit (DAC)
• On-board intelligence: powerful microprocessor and FPGA based state machine
• Three D/A converters for VCCP, VPP1, and VPP2, controllable rise and fall time
• VCCP range 0..8V/1A
• VPP1, VPP2 range 0..26V/1A
• Selftest capability
ZIF Socket
• 48-pin DIL ZIF socket accepts both 300/600 mil devices up to 48-pin
• Pindrivers: 48 universal
• VCCP/VPP1/VPP2 can be connected to each pin
• Perfect ground for each pin
• FPGA based TTL driver provides H, L, CLK, pull-up, pull-down on all pindriver pins
• Analog pindriver output level selectable from 1.8V up to 26V
• Current limitation, overcurrent shutdown, power failure shutdown
• ESD protection on each pin (IEC1000-4-2: 15kV air, 8kV contact)
• Continuity test: each pin is tested before every programming operation
ISP Connector
• 20-pin male type with missinsertion lock
• 6 TTL pindrivers, provides H, L, CLK, pull-up, pull-down; level H selectable
• 1x VCCP voltage (range 2V..7V/100mA), can be applied to two pins
• Programmed chip voltage (VCCP) with both source/sink capability and
• 1x VPP voltage (range 2V..25V/50mA), can be applied to six pins
• Target system supply voltage (range 2V..6V/250mA)
• ESD protection on each pin (IEC1000-4-2: 15kV air, 8kV contact)
• Two output signals, which indicate state of work result = LED OK and LED
• Input signal, switch YES! equivalent (active level: max. 0.8V)
Software:
User Interface
Production Mode Control
• This part of the software is focused to the easy monitoring of high-volume
• Operator-friendly control software combines many powerful functions with
• Project files are used to control the 448Pro2 and contain user data, chip
IN THE UK…
Dataman Programmers Ltd.
Station Road, Maiden Newton
Dorset DT2 0AE, UK
Tel [phone]
Fax [phone]
connectors)
from 1.8V up to 5V to handle all (including low-voltage) devices
voltage sense
Error (active level: min 1.8V)
production operations.
ease of use. Graphic user interface provides an overview of important
information, reducing the burden on the operator with unnecessary details.
programming setup, chip configuration, auto programming command
IN THE US…
Dataman Inc.
215 East Michigan Avenue
Orange City, Florida 32763 USA
Tel [phone]
Fax [phone]
• Each chip may be programmed with different data such as serial number,
Engineering Mode Control
• This part of the software is focused to the quick and easy preparation of the
• Each programming module is driven by an easy-to-use control program with
• Standard device-related commands (read, blank check, program, verify, erase)
• All known data formats are supported. Automatic file format detection and
• The software provides extensive information about programmable devices
The Dataman 448Pro2 supports over 51,000 (Jan 2010) of the most popular
devices in use today - with future devices being added monthly. Dataman
448Pro2 coverage includes the following device types:
Programmer (ZIF Socket)
EPROM, EEPROM, Flash EPROM, NAND Flash, LBA-NAND, mDOC H3, multi-chip
devices, FRAM, MRAM, NV RAM, PROM, Serial E(E)PROM, Serial Flash,
Configuration (EE)PROM, 1-Wire E(E)PROM, PLD, FPGA, Clocks, Microcontrollers
Programmer (ISP Connector)
Serial E(E)PROM, 1-Wire E(E)PROM, Serial Flash, Microcontrollers, PLD, FPGA
Package Includes:
• Dataman 448Pro2 Super Fast Gang ISP Production Programmer
• Moulded USB cable
• ISP cable (x4)
• Diagnostic POD for selftest of the programmer (x1)
• Diagnostic POD for selftest of the ISP connector (x1)
• Anti-dust cover for ZIF socket (x4)
• ESD wrist strap with cord and banana plug
• Vacuum pen
• User manual
• Software
• Transport case
• Optional range of adapters and socket converters also available
Warranty and Support
• 30 day money back guarantee* - If you don't like it, send it back.
• Three year guarantee - Three years parts and labour warranty, on the
• Life-Time Technical Support - 448Pro2 technical support is available free via
• "Life-Time Software Updates – 448Pro2 software updates are available free
*Applies to orders from UK/US offices only
sequence. This helps minimize operator error as the project file is normally
created by an engineer and then passed to the operator. The optional
protected mode can be set avoiding unwanted changes to the project file.
configuration and calibration information.
project file for usage in the production mode control software.
pull-down menus, hot keys and on-line help. Selecting a device is performed
by its class, by manufacturer or simply by typing a fragment of the vendor
name and/or part number.
are enhanced by test functions (insertion test, signature-byte check) and
additional special functions (auto-increment serialisation, production mode -
programming starts immediately after chip is inserted).
conversion performed during loading of file.
including detailed drawings of all available packages. The software also
provides explanations of chip labelling (prefixes and suffixes).
Dimensions: 361 x 234 x 56mm (14.2 x 9.2 x 2.2inches)
Weight: 3.5Kg (7.72lbs)
Operating voltage: 100-240V AC
Power consumption: max. 60W active
448Pro2 universal gang programmer.
our website and telephone helpdesk for life.
via our website for life.
Available from…
www.dataman.com