12292 Loctite, 12292 Datasheet
![ETHYL CYANOACRYLATE ADH, BOTTLE 20G](/photos/24/33/243346/4608011_sml.jpg)
12292
Manufacturer Part Number
12292
Description
ETHYL CYANOACRYLATE ADH, BOTTLE 20G
Manufacturer
Loctite
Series
444r
Datasheet
1.12292.pdf
(2 pages)
Specifications of 12292
Adhesive Type
Ethyl Cyanoacrylate
Color
Clear
Dispensing Method
Bottle
Weight
20g
Pack Quantity
1
Mil Spec
MIL-A-46050C, Type II, Class 3
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
PRODUCT DESCRIPTION
LOCTITE
characteristics:
LOCTITE
cyanoacrylate adhesive formulated for electronics applications.
LOCTITE
Accelerators to attain instant cures for tacking electronics
components . Typical applications include wire tacking to coil
forms; tamper proofing adjustable components; mounting
standoffs, edge guides and stiffeners to circuit boards.
Commercial Item Description A-A-3097:
LOCTITE
Description A-A-3097. Note: This is a regional approval.
Please contact your local Technical Service Center for more
information and clarification.
TYPICAL PROPERTIES OF UNCURED MATERIAL
TYPICAL CURING PERFORMANCE
Under normal conditions, the atmospheric moisture initiates the
curing process. Although full functional strength is developed
in a relatively short time, curing continues for at least 24 hours
before full chemical/solvent resistance is developed.
Cure Speed vs. Bond Gap
The rate of cure will depend on the bondline gap. Thin bond
lines result in high cure speeds, increasing the bond gap will
decrease the rate of cure.
Cure Speed vs. Activator
Where cure speed is unacceptably long due to large gaps,
applying activator to the surface will improve cure speed.
However, this can reduce ultimate strength of the bond and
therefore testing is recommended to confirm effect.
Technology
Chemical Type
Appearance
Components
Viscosity
Cure
Application
Key Substrates
Specific Gravity @ 25 °C
Viscosity, Brookfield - LVF, 25 °C, mPa·s (cP):
Flash Point - See MSDS
Spindle 2, speed 30 rpm
®
®
®
®
444™
444™ is a single part, fast curing medium viscosity
444™ is designed to use with TAK PAK
444™
has been qualified to Commercial Item
provides
Cyanoacrylate
Ethyl cyanoacrylate
Colorless transparent liquid
One part - requires no mixing
Medium
Humidity
Bonding
Rubbers, Plastics and Metals
the
following
550 to 850
1.05
LMS
product
LMS
®
TYPICAL PROPERTIES OF CURED MATERIAL
TYPICAL PERFORMANCE OF CURED MATERIAL
GENERAL INFORMATION
This product is not recommended for use in pure oxygen
and/or oxygen rich systems and should not be selected as
a sealant for chlorine or other strong oxidizing materials
For safe handling information on this product, consult the
Material Safety Data Sheet (MSDS).
Directions for use:
After 24 hours @ 22 °C
Cured for 2 minutes @ 22 °C
1. Apply one coating of TAK PAK
2. Allow the accelerator time to evaporate under good
Physical Properties:
Electrical Properties:
Lap Shear Strength, ISO 4587:
Coefficient
Expansion,
Coefficient
Conductivity, ISO 8302,
W/(m·K)
Glass Transition Temperature,
ASTM E 228, °C
Volume Resistivity, IEC 60093,
Ω·cm
Surface Resistivity, IEC 60093,
Ω
Dielectric Breakdown Strength,
IEC 60243-1, kV/mm
Dielectric Constant / Dissipation Factor, IEC 60250:
Steel (grit blasted)
ISO 11359-2, K
be bonded, by spray, brush or dipping.
application, contaminated surfaces may need special
cleaning or degreasing to remove any dissolvable
contamination.
NOTE: Because the solvent base of TAK PAK
can affect certain plastics or coatings, checking all surfaces for
compatibility is recommended.
.
ventilation until the surfaces are completely dry (approx.
15 to
1-kHz
30-
seconds)..
LOCTITE
-1
of
of
Thermal
Thermal
80×10
0.11
130
7.2×10
66×10
36.6
®
accelerator to the area to
Technical Data Sheet
-5
15
15
®
N/mm²
(psi)
3.0 / 0.028
444™
®
March-2010
(≥780)
≥5.4
accelerators
Prior to
LMS
12292 Summary of contents
Page 1
... NOTE: Because the solvent base of TAK PAK can affect certain plastics or coatings, checking all surfaces for compatibility is recommended Allow the accelerator time to evaporate under good ventilation until the surfaces are completely dry (approx 30- Technical Data Sheet ® LOCTITE 444™ March-2010 of Thermal 80× Thermal ...
Page 2
... Secure the assembly and await fixturing before any further handling.. Loctite Material Specification LMS LMS dated December-28, 1999. Test reports for each batch are available for the indicated properties. LMS test reports include selected QC test parameters considered appropriate to specifications for customer use ...