22231 Loctite, 22231 Datasheet - Page 3

• Manufacturer Part Number: 22231
• Description: ACRYLIC ADHESIVE, BOTTLE, 50ML
• Manufacturer: Loctite
• Series: 222MSr

Specifications of 22231

• Adhesive Type: Acrylic
• Adhesive Applications: Thread Locking
• Color: Purple
• Dispensing Method: Bottle
• Volume: 50ml
• Mil Spec: MIL-S-46163A For Existing Designs, ASTM D-5363, NSF P1, CFIA
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

Heat Aging
Aged at temperature indicated and tested @ 22 °C
Chemical/Solvent Resistance
Aged under conditions indicated and tested @ 22 °C.
GENERAL INFORMATION
This product is not recommended for use in pure oxygen
and/or oxygen rich systems and should not be selected as
a sealant for chlorine or other strong oxidizing materials
For safe handling information on this product, consult the
Material Safety Data Sheet (MSDS).
Where aqueous washing systems are used to clean the
surfaces before bonding, it is important to check for
compatibility of the washing solution with the adhesive. In
some cases these aqueous washes can affect the cure and
performance of the adhesive.
This product is not normally recommended for use on plastics
(particularly thermoplastic materials where stress cracking of
the plastic could result). Users are recommended to confirm
compatibility of the product with such substrates.
Directions for use:
Henkel Americas
+860.571.5100
Environment
Motor oil
Leaded Petrol
Brake fluid
Water/glycol 50/50
Acetone
Ethanol
For Assembly
1. For best results, clean all surfaces (external and
2. If the material is an inactive metal or the cure speed is
3. Shake the product thoroughly before use.
4. To prevent the product from clogging in the nozzle, do
125
100
75
50
25
internal) with a LOCTITE
dry.
too slow, spray all threads with and allow to dry.
not allow the tip to touch metal surfaces during
application.
0
For the most direct access to local sales and technical support visit: www.henkel.com/industrial
0
1000
125
°C
22
22
87
22
22
2000
100 h
100
100
®
95
95
80
95
cleaning solvent and allow to
% of initial strength
3000
500 h
95
95
95
80
90
95
1000 h
4000
90
95
95
80
90
90
+49.89.320800.1800
5000 h
85
95
90
80
90
90
5000
Henkel Europe
Loctite Material Specification
LMS dated December-7, 1999. Test reports for each batch are
available for the indicated properties. LMS test reports include
selected QC test parameters considered appropriate to
specifications for customer use. Additionally, comprehensive
controls are in place to assure product quality and
consistency. Special customer specification requirements may
be coordinated through Henkel Quality.
Storage
Store product in the unopened container in a dry location.
Storage information may be indicated on the product container
labeling.
Optimal Storage: 8 °C to 21 °C. Storage below 8 °C or
greater than 28 °C can adversely affect product properties.
Material removed from containers may be contaminated during
use. Do not return product to the original container. Henkel
Corporation cannot assume responsibility for product which
has been contaminated or stored under conditions other than
those previously indicated. If additional information is required,
please contact your local Technical Service Center or
Customer Service Representative.
Conversions
(°C x 1.8) + 32 = °F
kV/mm x 25.4 = V/mil
mm / 25.4 = inches
µm / 25.4 = mil
N x 0.225 = lb
N/mm x 5.71 = lb/in
N/mm² x 145 = psi
MPa x 145 = psi
N·m x 8.851 = lb·in
N·m x 0.738 = lb·ft
N·mm x 0.142 = oz·in
mPa·s = cP
For Disassembly
For Cleanup
5. For Thru Holes, apply several drops of the product onto
6. For Blind Holes, apply several drops of the product
7. Assemble and tighten as required.
8. For Sealing Applications, apply a 360° bead of product
1. Remove with standard hand tools.
2. In rare instances where hand tools do not work because
1. Cured product can be removed with a combination of
the bolt at the nut engagement area.
down the internal threads to the bottom of the hole.
to the leading threads of the male fitting, leaving the first
thread free. Force the material into the threads to
thouroughly fill the voids. For bigger threads and voids,
adjust product amount accordingly and apply a 360°
bead of product on the female threads also.
of excessive engagement length, apply localized heat to
nut or bolt to approximately 250 °C. Disassemble while
hot.
soaking in a Loctite solvent and mechanical abrasion
such as a wire brush.
TDS LOCTITE
LMS
®
222MS™, October-2009
Henkel Asia Pacific
+86.21.2891.8863