27240 Loctite, 27240 Datasheet - Page 2

• Manufacturer Part Number: 27240
• Description: ACRYLIC ADHESIVE, BOTTLE, 50ML
• Manufacturer: Loctite
• Series: 272r

Specifications of 27240

• Adhesive Type: Acrylic
• Color: Red
• Dispensing Method: Bottle
• Volume: 50ml
• Pack Quantity: 1
• Mil Spec: CFIA Agency Approval
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

TYPICAL ENVIRONMENTAL RESISTANCE
Hot Strength
Tested at temperature
Chemical/Solvent Resistance
Aged under conditions indicated and tested @ 22°C.
Henkel Americas
+860.571.5100
Environment
Air reference
Motor oil (MIL-L-46152)
Gasoline
Water
Processing
Temperature
Toluene
Phosphate ester
Cured for 24 hours @ 22 °C followed by 72 hours @ 200 °C, tested
@ 200 °C
Cured for 24 hours @ 22 °C
Prevail Torque, ISO 10964:
Compressive Shear Strength, ISO 10123:
Compressive Shear Strength, ISO 10123:
Breakaway Torque, ISO 10964:
M10 steel nuts and bolts
3/8 x 16 steel nuts (grade
2) and bolts (grade 5)
Steel pins and collars
Steel pins and collars
M10 steel nuts and bolts
100
75
50
25
0
For the most direct access to local sales and technical support visit: www.henkel.com/industrial
0
50
°C
87
87
87
87
87
87
87
100
% of initial strength
N·m
(lb.in.)
N·m
(lb.in.)
N/mm²
(psi)
N/mm²
(psi)
720 h
100
62
62
58
87
80
70
(≥2,102)
(≥2,900)
(220)
(≥159)
25
≥18
150
≥14.5
≥20
LMS
LMS
LMS
+49.89.320800.1800
Henkel Europe
200
GENERAL INFORMATION
This product is not recommended for use in pure oxygen
and/or oxygen rich systems and should not be selected as
a sealant for chlorine or other strong oxidizing materials
For safe handling information on this product, consult the
Material Safety Data Sheet (MSDS).
Where aqueous washing systems are used to clean the
surfaces before bonding, it is important to check for
compatibility of the washing solution with the adhesive. In
some cases these aqueous washes can affect the cure and
performance of the adhesive.
This product is not normally recommended for use on plastics
(particularly thermoplastic materials where stress cracking of
the plastic could result). Users are recommended to confirm
compatibility of the product with such substrates.
Directions for use:
For Assembly
For Disassembly
For Cleanup
Loctite Material Specification
LMS dated February-14, 2000. Test reports for each batch are
available for the indicated properties. LMS test reports include
selected QC test parameters considered appropriate to
specifications for customer use. Additionally, comprehensive
controls are in place to assure product quality and
consistency. Special customer specification requirements may
be coordinated through Henkel Quality.
1. For best results, clean all surfaces (external and internal)
2. If the material is an inactive metal or the cure speed is too
3. To prevent the product from clogging in the nozzle, do not
4. For Thru Holes, apply several drops of the product onto
5. For Blind Holes, apply several drops of the product down
6. For Sealing Applications, apply a 360° bead of product
7. Assemble and tighten as required.
1. Apply localized heat to nut or bolt to approximately 250
1. Cured product can be removed with a combination of
with a LOCTITE
slow, spray all threads with and allow to dry.
allow the tip to touch metal surfaces during application.
the bolt at the nut engagement area.
the internal threads to the bottom of the hole.
to the leading threads of the male fitting, leaving the first
thread free. Force the material into the threads to
thouroughly fill the voids. For bigger threads and voids,
adjust product amount accordingly and apply a 360° bead
of product on the female threads also.
°C. Disassemble while hot.
soaking in a Loctite solvent and mechanical abrasion
such as a wire brush.
®
TDS LOCTITE
cleaning solvent and allow to dry.
LMS
®
272™, December-2008
Henkel Asia Pacific
+86.21.2891.8863