68015 Loctite, 68015 Datasheet - Page 3

• Manufacturer Part Number: 68015
• Description: ACRYLIC ADHESIVE, BOTTLE, 10ML
• Manufacturer: Loctite
• Series: 680r

Specifications of 68015

• Adhesive Type: Acrylic
• Color: Green
• Dispensing Method: Bottle
• Volume: 10ml
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

GENERAL INFORMATION
This product is not recommended for use in pure oxygen
and/or oxygen rich systems and should not be selected as
a sealant for chlorine or other strong oxidizing materials
For safe handling information on this product, consult the
Material Safety Data Sheet (MSDS).
Where aqueous washing systems are used to clean the
surfaces before bonding, it is important to check for
compatibility of the washing solution with the adhesive. In
some cases these aqueous washes can affect the cure and
performance of the adhesive.
This product is not normally recommended for use on plastics
(particularly thermoplastic materials where stress cracking of
the plastic could result). Users are recommended to confirm
compatibility of the product with such substrates.
Directions for use:
For Assembly
For Disassembly
For Cleanup
Loctite Material Specification
LMS dated August-23, 1999. Test reports for each batch are
available for the indicated properties. LMS test reports include
selected QC test parameters considered appropriate to
specifications for customer use. Additionally, comprehensive
controls are in place to assure product quality and
consistency. Special customer specification requirements may
be coordinated through Henkel Quality.
Henkel Americas
+860.571.5100
1. For best results, clean all surfaces (external and internal)
2. If the material is an inactive metal or the cure speed is too
3. For Slip Fitted Assemblies, apply adhesive around the
4. For Press Fitted Assemblies, apply adhesive thoroughly
5. For Shrink Fitted Assemblies the adhesive should be
6. Parts should not be disturbed until sufficient handling
1. Apply localized heat to the assembly to approximately
1. Cured product can be removed with a combination of
with a LOCTITE
slow, spray with Activator 7471™ or 7649™ and allow to
dry.
leading edge of the pin and the inside of the collar and
use a rotating motion during assembly to ensure good
coverage.
to both bond surfaces and assemble at high press on
rates.
coated onto the pin, the collar should then be heated to
create sufficient clearance for free assembly.
strength is achieved.
250 °C. Disassemble while hot.
soaking in a Loctite solvent and mechanical abrasion
such as a wire brush.
For the most direct access to local sales and technical support visit: www.henkel.com/industrial
®
cleaning solvent and allow to dry.
LMS
+49.89.320800.1800
Henkel Europe
Long Term Storage
Store product in the unopened container in a dry location.
Storage information may be indicated on the product container
labeling.
Optimal Storage: 8 °C to 21 °C. Storage below 8 °C or
greater than 28 °C can adversely affect product properties.
Material removed from containers may be contaminated during
use. Do not return product to the original container. Henkel
cannot assume responsibility for product which has been
contaminated or stored under conditions other than those
previously indicated. If additional information is required,
please contact your local Technical Service Center or
Customer Service Representative.
Conversions
(°C x 1.8) + 32 = °F
kV/mm x 25.4 = V/mil
mm / 25.4 = inches
µm / 25.4 = mil
N x 0.225 = lb
N/mm x 5.71 = lb/in
N/mm² x 145 = psi
MPa x 145 = psi
N·m x 8.851 = lb·in
N·m x 0.738 = lb·ft
N·mm x 0.142 = oz·in
mPa·s = cP
Note
The data contained herein are furnished for information only
and are believed to be reliable.
responsibility for the results obtained by others over whose
methods we have no control. It is the user's responsibility to
determine suitability for the user's purpose of any production
methods mentioned herein and to adopt such precautions as
may be advisable for the protection of property and of persons
against any hazards that may be involved in the handling and
use thereof. In light of the foregoing, Henkel Corporation
specifically disclaims all warranties expressed or implied,
including warranties of merchantability or fitness for a
particular purpose, arising from sale or use of Henkel
Corporation’s products. Henkel Corporation specifically
disclaims any liability for consequential or incidental
damages of any kind, including lost profits. The discussion
herein of various processes or compositions is not to be
interpreted as representation that they are free from
domination of patents owned by others or as a license under
any Henkel Corporation patents that may cover such
processes or compositions.
prospective user test his proposed application before repetitive
use, using this data as a guide. This product may be covered
by one or more United States or foreign patents or patent
applications.
Trademark usage
Except as otherwise noted, all trademarks in this document
are trademarks of Henkel Corporation in the U.S. and
elsewhere.
Patent and Trademark Office.
Reference 1.3
®
denotes a trademark registered in the U.S.
TDS LOCTITE
We recommend that each
®
680™, December-2009
We cannot assume
Henkel Asia Pacific
+86.21.2891.8863