7360 Loctite, 7360 Datasheet
7360
Manufacturer Part Number
7360
Description
EPOXY ADHESIVE REMOVER/SOLVENT, BOTTLE, 500ML
Manufacturer
Loctite
Datasheet
1.7360.pdf
(2 pages)
Specifications of 7360
Cleaner Type
Adhesive Remover
Cleaner Applications
Circuit Boards, Electronics
Dispensing Method
Bottle
Volume
500ml
Chemical Solution
Aliphatic Ester Blend
Color
Clear
Rohs Compliant
Yes
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
PRODUCT DESCRIPTION
7360™ provides the following product characteristics:
7360™ is a non-CFC, low odor, solvent based formulation
intended for the removal of uncured adhesive and adhesive
residues used in the PCB assembly industry. The solvent is
fully compatible with epoxy adhesives and will not cause
hardening during soaking. 7360™ is recommended for
cleaning of stencils, screens and dispensing nozzles used to
apply surface mount adhesives and for removal of adhesives
from misprinted circuit boards.
TYPICAL PROPERTIES
TYPICAL PERFORMANCE
7360™ has no effect on the speed of cure or final strength of
LOCTITE
good adhesion and adhesive cure. Unclean or partially
cleaned surfaces can affect adhesive performance. The
solvent is fully compatible with commonly used solder resists.
GENERAL INFORMATION
This product is not recommended for use in pure oxygen
and/or oxygen rich systems and should not be selected
with a sealant for chlorine or other strong oxidizing
materials.
For safe handling information on this product, consult the
Material Safety Data Sheet (MSDS).
Directions for use:
Technology
Chemical Type
Appearance
Viscosity
Cure
Application
Specific Gravity @ 25 °C
Infrared Spectrum
Viscosity @ 20°C, mPa·s (cP)
TLV (ACGIH), ppm
Flash Point - See MSDS
It is advisable to use protective clothing to avoid contact with
the solvent and adhesive. The low volatility of this solvent
makes it ideal for open reservoirs but does mean that it
requires drying by cloth or compressed air.
Cleaning Dispenser Needles & Components - using spray
can with extension tube and tip
1. The simplest and most effective cleaning is to "jet spray"
the uncured adhesive out of the needle bore by ensuring
a snug fit between the tip on the extension tube and the
®
adhesives other than providing a clean surface for
Solvent cleaner
Aliphatic ester blend
Clear colorless solution
Very low
Not applicable
Solvent for uncured SM adhesives
1.09
As standard
2.5
100
LMS
LMS
Loctite Material Specification
LMS dated December-01, 2004. Test reports for each batch
are available for the indicated properties. LMS test reports
include selected QC test parameters considered appropriate to
specifications for customer use. Additionally, comprehensive
controls are in place to assure product quality and
consistency. Special customer specification requirements may
be coordinated through Henkel Quality.
Using Ultrasonic or Static Bath
Cleaning Boards, Stencils, Wiper Blades
Note:
2. Dry out needle by blowing through bore using dry
3. Check for cleanliness and that no blockage remains.
1. Uncured adhesive should be mechanically removed as
2. Immerse items to be cleaned in a reservoir of fresh
3. If using an ultrasonic bath, set at maximum power for 3
4. If using a static bath, use tweezers to agitate the items in
5. For needles with very small bores or cavities it is
6. Dry out parts and blow through bore using dry
1. Apply solvent direct from can to dry lint free cloth, or
2. Wipe away uncured adhesive (one wipe is usually
3. Dry surface with a clean dry cloth.
● All dispensing parts being cleaned may be left to soak
● While the solvent has been checked for compatibility
● Needle blockages due to cured or partially cured
needle. (The tip can be cut to suit different needle types)
.
compressed air.
much as possible by using a blunt tool for any larger
cavities and a drill bit or piano wire of appropriate
diameter for the needle bore. This operation helps
minimize solvent usage.
solvent.
the bath until solvent has become stained due to
removal of adhesive. Rinse in fresh solvent to confirm
cleanliness.
recommended to follow with a "jet spray" clean as
previously described.
compressed air.
spray directly onto adhesive on surface to be cleaned.
sufficient).
for several days witout risk of hardening the adhesive or
adversely affecting the material being cleaned.
with materials commonly used in PCB assembly, certain
plastics or coatings may be affected and should be
checked for compatibility before use.
adhesive should be cleared using a drill bit before
solvent cleaning.
minutes at 40 °C.
LMS
Technical Data Sheet
7360™
April-2008
7360 Summary of contents
Page 1
... Infrared Spectrum Viscosity @ 20°C, mPa·s (cP) TLV (ACGIH), ppm Flash Point - See MSDS TYPICAL PERFORMANCE 7360™ has no effect on the speed of cure or final strength of ® LOCTITE adhesives other than providing a clean surface for good adhesion and adhesive cure. Unclean or partially cleaned surfaces can affect adhesive performance. The solvent is fully compatible with commonly used solder resists ...
Page 2
... U.S. Patent and Trademark Office. Reference 1.1 Henkel Americas +949.789.2500 For the most direct access to local sales and technical support visit: www.henkel.com/electronics We cannot assume Henkel Europe +44.1442.278.000 TDS 7360™, April-2008 Henkel Asia Pacific +86.21.2891.8000 ...