18580 Loctite, 18580 Datasheet

18580

Manufacturer Part Number

18580

Description

7452(TM) Tak Pak(R) Accelerator, 1.75 Oz. Spray-Cap Bottle

Manufacturer

Loctite

Series

7452r

Datasheet

1.18490.pdf (2 pages)

Specifications of 18580

Rohs Compliant

Yes

Adhesive Type

Activator

Adhesive Applications

Surface Priming / Cure Acceleration

Color

Transparent Colorless To Slightly Amber Liquid

Dispensing Method

Spray Bottle

Lead Free Status / RoHS Status

Lead free / RoHS Compliant

Current page: 1 of 2
Download datasheet (59Kb)

PRODUCT DESCRIPTION

LOCTITE

characteristics:

LOCTITE

either pre- or post-applied to the bond. The product is

especially

adhesive to ensure rapid fixturing. Typical applications include

securing wires or coils to PCBs, tamper-proofing adjustable

components, mounting stand-offs, edge guides and board

stiffeners.

TYPICAL PROPERTIES

TYPICAL PERFORMANCE

Fixture time and cure speed achieved as a result of using

LOCTITE

substrate bonded.

(Fixture time is defined as the time to develop a shear strength

of 0.1 N/mm²)

Handling precautions

Activator must be handled in a manner applicable to highly

flammable materials and in compliance with relevant local

regulations.

The solvent can affect certain plastics or coatings. It is

recommended to check all surfaces for compatibility before

use.

GENERAL INFORMATION

This product is not recommended for use in pure oxygen

and/or oxygen rich systems and should not be selected

with a sealant for chlorine or other strong oxidizing

materials.

Technology

Chemical Type

Solvent

Active Ingredient

Concentration, %

Appearance

Viscosity

Cure

Application

Fixture Time, ISO 4587, seconds:

Specific Gravity @ 25 °C

Viscosity @ 20 °C, mPa·s (cP)

Drying Time @ 20 °C, seconds

On Part Life, minutes

Infrared Spectrum

Flash Point - See MSDS

Steel (grit blasted) using LOCTITE

two side activation

cyanoacrylate adhesives is required. It can be

7452™ is used where increased cure speed of

7452™ depend on the adhesive used and the

suited

7452™

for

provides

Cyanoacrylate Activator

Amine (active ingredient)

Acetone

0.8 to 0.95

Transparent

amber liquid

Very low

Not applicable

CA adhesive cure accelerator

post-application

495™,

LMS

the

LMS

colorless

To match standard

following

cyanoacrylate

0.3 to 0.5

0.79

≤30

≤1

≤10

product

slightly

LMS

For safe handling information on this product, consult the

Material Safety Data Sheet (MSDS).

Under no circumstances should activator and adhesive be

mixed directly as liquids. Use only in a well ventilated area.

Directions for use

Post Activation

Surface Activation

Loctite Material Specification

LMS dated May-19, 1998. Test reports for each batch are

available for the indicated properties. LMS test reports include

selected QC test parameters considered appropriate to

specifications for customer use. Additionally, comprehensive

controls are in place to assure product quality and

consistency. Special customer specification requirements may

be coordinated through Henkel Quality.

Storage

This activator is classified as HIGHLY FLAMMABLE and

must be stored in an appropriate manner in compliance with

relevant regulations. Do not store near oxidising agents or

combustible materials. The product is light sensitve and

accordingly, translucent containers should be kept in a dark

place when not in use. Store product in the unopened

container in a dry location. Storage information may also be

indicated on the product container labelling.

Optimal Storage: 8 °C to 21 °C. Storage below 8 °C or

greater than 28 °C can adversely affect product properties

Material removed from containers may be contaminated during

use. Do not return product to the original container. Henkel

cannot assume responsibility for product which has been

contaminated or stored under conditions other than those

previously indicated. If additional information is required,

please contact your local Technical Service Center or

Customer Service Representative.

1. Apply Loctite cyanoacrylate to the parts to be bonded or

2. Apply Activator over all exposed cyanoacrylate adhesive

1. Apply one coating of Activator to the area to be bonded by

2. Allow LOCTITE

3. Apply the Loctite cyanoacrylate product immediately after

4. Activator can be re-applied if necessary if there is a delay

fixed.

by spray or drop. (Typically use one drop of activator per

drop of exposed adhesive).

spray, brush or dipping. Contaminated surfaces may need

special cleaning or degreasing prior to activation to

remove any soluble contamination.

prior to bonding to avoid solvent entrapment within the

bond joint.

drying or not more than

of more than

adhesive application.

LOCTITE

45-

seconds between original activator and

7452™ to fully evaporate from parts

45-

LMS

seconds thereafter.

Technical Data Sheet

7452™

November-2008

18580 Summary of contents

Page 1

... Material Safety Data Sheet (MSDS). following product Under no circumstances should activator and adhesive be mixed directly as liquids. Use only in a well ventilated area. Directions for use Post Activation 1. Apply Loctite cyanoacrylate to the parts to be bonded or colorless to slightly fixed. LMS 2. Apply Activator over all exposed cyanoacrylate adhesive by spray or drop ...

Page 2

... U.S. Patent and Trademark Office. Reference 1.1 Henkel Americas +860.571.5100 For the most direct access to local sales and technical support visit: www.henkel.com/industrial We cannot assume Henkel Europe +49.89.320800.1800 ® TDS LOCTITE 7452™, November-2008 Henkel Asia Pacific +86.21.2891.8863 ...