980-2000-923 ITT Cannon, 980-2000-923 Datasheet - Page 42
![CRIMP SOCKET, OPEN 20-24AWG](/photos/24/43/244374/1560033-40_sml.jpg)
980-2000-923
Manufacturer Part Number
980-2000-923
Description
CRIMP SOCKET, OPEN 20-24AWG
Manufacturer
ITT Cannon
Series
ZDr
Datasheet
1.121086-3303.pdf
(44 pages)
Specifications of 980-2000-923
Connector Type
D Sub Contact
Contact Plating
Gold
Contact Material
Copper Alloy
Wire Size Range (awg)
20
Gender
Socket
Svhc
No SVHC (18-Jun-2010)
Connector
RoHS Compliant
Contact Termination
Crimp
Wire Size (awg)
24 To 20 AWG
Contact Gender
Socket
Contact Type
Stamped
Rohs Compliant
Yes
For Use With
D Sub Connectors
1. MATERIAL CONTENT AND PHYSICAL
FORM
Electrical connectors do not usually contain
hazardous materials. They contain conduct-
ing and non-conducting materials and can
be divided into two groups.
a) Printed circuit types and low cost audio
types which employ all plastic insulators and
casings.
b) Rugged, Fire Barrier and High Reliability
types with metal casings and either natural
rubber, synthetic rubber, plastic or glass
insulating materials. Contact materials vary
with type of connector and also application
and are usually manufactured from either:
Copper, copper alloys, nickel, alumel,
chromel or steel. In special applications,
other alloys may be specified.
2. FIRE CHARACTERISTICS AND ELECTRIC
SHOCK HAZARD
There is no fire hazard when the connec-
tor is correctly wired and used within the
specified parameters. Incorrect wiring or
assembly of the connector or careless use
of metal tools or conductive fluids, or
transit damage to any of the component
parts may cause electric shock or burns.
Live circuits must not be broken by sepa-
rating mated connectors as this may
cause arcing, ionization and burning. Heat
dissipation is greater at maximum resistance
in a circuit. Hot spots may occur when resist-
ance is raised locally by damage, e.g. cracked
or deformed contacts, broken strands of
wire. Local overheating may also result from
the use of the incorrect application tools or
from poor quality soldering or slack screw
terminals. Overheating may occur if the rat-
ings in the product Data Sheet/Catalog are
exceeded and can cause breakdown of insu-
lation and hence electric shock. If heating is
allowed to continue it intensifies by further
increasing the local resistance through loss
of temper of spring contacts, formation of
oxide film on contacts and wires and leakage
currents through carbonization of insulation
and tracking paths. Fire can then result in
the presence of combustible materials and
this may release noxious fumes. Overheating
may not be visually apparent. Burns may
result from touching overheated compo-
nents.
3. HANDLING
Care must be taken to avoid damage
to any component parts of electrical connec-
tors during installation and use. Although
there are normally no sharp edges, care
must be taken when handling certain com-
ponents to avoid injury to fingers. Electrical
connectors may be damaged in transit to the
customers, and damage may result in cre-
ation of hazards. Products should therefore
be examined prior to installation/use and
rejected if found to be damaged.
4. DISPOSAL
Cannon ZD Connectors
Incineration of certain materials may release
noxious or even toxic fumes.
5. APPLICATION
Connectors with exposed contacts should
not be selected for use on the current supply
side of an electrical circuit, because an elec-
tric shock could result from touching
exposed contacts on an unmated connector.
Voltages in excess of 30 V ac or 42.5 V dc are
potentially hazardous and care should be
taken to ensure that such voltages cannot be
transmitted in any way to exposed metal
parts of the connector body. The connector
and wiring should be checked, before mak-
ing live, to have no damage to metal parts or
insulators, no solder blobs, loose strands,
conducting lubricants, swarf, or any other
undesired conducting particles. Circuit
resistance and continuity check should be
made to make certain that there are no high
resistance joints or spurious conducting
paths. Always use the correct application
tools as specified in the Data Sheet/Catalog.
Do not permit untrained personnel to wire,
assemble or tamper with connectors. For
operation voltage please see appropriate
national regulations.
IMPORTANT GENERAL INFORMATION
(i) Air and creepage paths/Operating volt-
age. The admissible operating voltages
depend on the individual applications and
the valid national and other applicable safe-
ty regulations.
For this reason the air and creepage path
data are only reference values. Observe
reduction of air and creepage paths due to
PC board and/or harnessing.
(ii) Temperature
All information given are temperature limits.
The operation temperature depends on the
individual application.
(iii) Other important information
Cannon continuously endeavors to improve
their products. Therefore, Cannon products
may deviate from the description, technical
data and shape as shown in this catalog and
data sheets.
“Engineered for life” is a registered trade-
mark of ITT Corporation, ©2006. All other
trademarks or registered trademarks are
property of their respective owners. All data
subject to change without notice.
42
Product Warranty
ITT Electronic Components, a Division of ITT
Corporation manufactures the highest qual-
ity products available in the marketplace;
however these products are intended to be
used in accordance with the specifications in
this publication. Any use or application that
deviates from the stated operating specifica-
tions is not recommended and may be
unsafe. No information and data contained
in this publication shall be construed to cre-
ate any liability on the part of Cannon. Any
new issue of this publication shall automati-
cally invalidate and supersede any and all
previous issues. A limited warranty applies to
Cannon products. Except for obligations
assumed by Cannon under this warranty,
Cannon shall not be liable for any loss, dam-
age, cost of repairs, incidental or consequen-
tial damages of any kind, whether or not
based on express or implied warranty, con-
tract, negligence or strict liability arising in
connection with the design, manufacture,
sale, use or repair of the products. Product
availability, prices and delivery dates are
exclusively subject to our respective order
confirmation form; the same applies to
orders based on development samples deliv-
ered. This publication is not to be construed
as an offer. It is intended merely as an invita-
tion to make an offer. By this publication,
Cannon does not assume responsibility or
any liability for any patent infringements or
other rights of third parties which may result
from its use. Reprinting this publication is
generally permitted, indicating the source.
However, Cannon's prior consent must be
obtained in all cases.
Specifications and dimensions subject to change
Dimensions shown in mm
www.ittcannon.com