82-816-1000 AMPHENOL RF, 82-816-1000 Datasheet

RF/COAXIAL, HN PLUG STR 50OHM CLAMP/SLDR

82-816-1000

Manufacturer Part Number
82-816-1000
Description
RF/COAXIAL, HN PLUG STR 50OHM CLAMP/SLDR
Manufacturer
AMPHENOL RF
Datasheet
1.16750.pdf (3 pages)

Specifications of 82-816-1000

Body Style
Straight Plug
Coaxial Termination
Solder / Clamp
Rg Cable Type
RG-108A
Contact Material
Brass
Contact Plating
Silver
Connector Type
HN Coaxial
Impedance
50ohm
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Assembly Instructions-C17
HN - Typical Clamp
Amphenol Corporation Tel: 800-627-7100
Nut
Gland
Gasket
Clamp
B
A
C
Contact
Female
291
Place nut, gland, and gasket, with "V" groove toward nut, over cable
and strip cable to dimensions as shown in table.
Comb out braid and fold out.
Pull braid wires forward and taper toward center conductor. Place
clamp over braid and push back against cable jacket.
Fold back braid wires as shown, trim to proper length and form over
clamp as shown. Solder contact to center conductor.
Insert cable and parts into connector body, make sure sharp edge of
clamp seats properly in gasket. Tighten nut.
Recommended Torque: 35-40 in lbs.
Stripping dims. inches (millimeters)
Amphenol
Part #
82-804
82-856
82-324
Jack Body
1.00 (25.4) .781 (19.8)
.680 (17.3)
1.59 (40.4) .875 (22.2)
a
.34 (8.6)
b
Contact
Male
.718 (18.2)
.219 (5.6)
.09 (2.3)
Amphenol
c
www.amphenolrf.com
Plug Body
®

Related parts for 82-816-1000

Image
Part Number
Description
Manufacturer
Datasheet
Request R
82-340
Part Number:
82-340
Description:
N COAX CONN CRIMP RG-8
Manufacturer:
AMPHENOL RF
Datasheet:
82-340.pdf (1 page)
82-63
Part Number:
82-63
Description:
N COAX CONN RECEPT RG-8
Manufacturer:
AMPHENOL RF
Datasheet:
82-63.pdf (1 page)
82-202
Part Number:
82-202
Description:
N COAX CONN RG-8, RG-213
Manufacturer:
AMPHENOL RF
Datasheet:
34025-RFX.pdf (1 page)
82-312
Part Number:
82-312
Description:
RF Connectors STRT CLMP PLG RG-8 UG-1185/U
Manufacturer:
Amphenol
Datasheet:
082-4427.pdf (1 page)
82-804
Part Number:
82-804
Description:
RF Connectors HN ST CLAMP PLUG RG-8 UG-59B/U
Manufacturer:
Amphenol
Datasheet:
82-804.pdf (1 page)
531-40047-3
Part Number:
531-40047-3
Description:
CONN F SOCKET R/A W/HARDWARE PCB
Manufacturer:
AMPHENOL RF
Datasheet:
531-40047-3.pdf (8 pages)
919-118J-51P
Part Number:
919-118J-51P
Description:
CONN MCX JACK STR 50 OHM SMD
Manufacturer:
AMPHENOL RF
Datasheet:
919-109J-51PX.pdf (8 pages)
031-71042
Part Number:
031-71042
Description:
CONN BNC JACK R/A 75 OHM PCB
Manufacturer:
AMPHENOL RF
Datasheet:
031-71042.pdf (1 page)

82-816-1000 Summary of contents

Page 1

... Part # a 82-804 1.00 (25.4) .781 (19.8) 82-856 .680 (17.3) B 82-324 1.59 (40.4) .875 (22.2) C Place nut, gland, and gasket, with "V" groove toward nut, over cable and strip cable to dimensions as shown in table. A Comb out braid and fold out. Pull braid wires forward and taper toward center conductor. Place clamp over braid and push back against cable jacket ...

Page 2

... Stripping dims. inches (millimeters) Amphenol Part # 16750 .799 (20.2) .594 (15.1) 82-816-1000 .843 (21.4) .625 (15.9) Push nut, washer and gasket over cable jacket. Cut cable even to dimensions shown in table. Push clamp over copper braid, flush against cable jacket. Cut exposed copper braid so that approximately 3/16 remains and fan over clamp ...

Page 3

... Cut end of cable even. Push nut, washer and gasket over cable jacket. Stripping dims. inches (millimeters) Amphenol Part # 82-38 Remove vinyl jacket .798" (20.3) from end of cable. For double shield cables, remove vinyl jacket 1 3/16" (30.2) from end of cable. c Push clamp over copper braid, flush against cable jacket. Cut exposed copper braid so that approximately .219" ...

Related keywords